3d printing first layer issues

(I would definitely suggest retracting when fitting the slider as it is a tight fit, and you could damage the tip of the wiper during assembly) I then recalibrated using raw data, and it is very smooth and accurate I printed this upside down with...

I am not sure what print settings were done as I outsourced locally and can't find the transcript. So on that unfortunately I won't be able to help. The wiring is not the best solution but I am working on a breakout board to utilise just 1x...

The smokestacks and the third level were lowered in one of the pictures so that the float could pass under approaching traffic lights.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament:...

As printed it the adapter should be a reasonable fit on that bar; if it is too tight to fit or adjust, clean the large hole with a round file or sandpaper, or put a 5/8" cutter through it. (I used a 5/8" Forstner bit, backwards - thread the shank...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

Having to make several 10+ hour prints to tune the shape resulted in some useless models and destroying those by hand took a lot of force, so I know this is strong and will hold up on very bumpy roads. See my other versions of this water bottle...

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

One uses 3mm rods glued in holes to support these, while the deeper one has a printed base and so a larger space for electronics. There's a groove at the rear for an aerial from the receiver, if it has two, so they can be at 90 degrees. The body lid...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

I borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also, if you change the hotend, you will need to run PID tuning otherwise the hotend won't get to temperature. And the induction...

Suggest the flange include a recess for the ring, then if wanted you can print a ring in TPU to assist with air leakage. Does not appear to be required.</p><p>Note, changing any of the settings (diameter, magnet size, alignment ring...) will change...

Place them in position at the Bottom print and ensure they are fully seated before beginning soldering. Once done, you can snip off the extending length of the pins. Depending on your printer's overhang capabilities, you may need supports for the...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...

Mount the printed spacers on the Raspberry board, by sliding them around the tubes. 6. Mount the 3.5” TFT screen on the Raspberry Pi board using the GPIO connector. 7. Mount the whole assembly on the right side of the main panel using four M3x10...

If you want to print dual color and are on version 4.7 or above, please either modify your gcode after you generate it or download a plug-in from the marketplace called Printer Settings. Then enable and check Extruders Share Heater and Extruders...

2016/10/16 New: 2S Light Version Available for Printing Polycarbonate - a Game-Changer in the RC World! This is an exciting development that is only compatible with the previous version of 2S. 2016/10/06 New: 2S Version with Adaptation to Lipo Bold...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

The box and face are printed in PLA with a color change for the digits. There is also an aligning part to glue (super glue) the face frame to the face. Also included is an LED removal tool – so you can support the back side to tap a failed Led...

If it interests you, the design can be modified: https://www.tinkercad.com/things/8xbdOSIT0zA-makita-eleksmaker-mount The files include: - The face plate holds the router clamp - The mount block (lose or solid) connects the face plate with z-axis...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

It's not intended to be printed (model was taken from McMaster Carr). ... Side Note: If you're wondering what the vise base thing is with all the alligator clips, etc., it's an awesome tool from Hobby Creek:...

edit 26.05.2021: Add more pictures with the end stop and also the length of the shaped tubes, detail picture of the brass nuts, add the link for the ball bearings, update the print settings. Please keep in mind this is not the cheapest one...

His robot arm uses three 28BYJ-48 steppers for the outmost joints: Please "like" this thing or post your make as a token of appreciation for my work. Find my other fischertechnik designs here. keywords: 28BYJ-48 28BYJ48 case enclosure...

With these horns, you will be able to make fine passes with the drill bit, so that you can cut a wood with fine drill bits or grind the copper of a printed circuit board. All this makes ScoposPlotter unique. Extensions for Inkscape v0.92 and grbl...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

[0] Thing Title : Personalized Soda Can Holder v2 [0] Thing URL : http://www.thingiverse.com/thing:6591 [0] Thing Author : JadeKnight [0] Thing Licence : Creative Commons - Attribution - Non-Commercial - Share Alike [1] Thing Title : Spider mount for...

This insert fits the Ark Nova base game and Marine Worlds expansion.In the pictures we've used alternate money tokens.Update Nov 9 2023: added sleeve_holder_2_v2 as replacement for card_holder_2 if you sleeve your cards.Update Nov 11 2023:Updated...

Printed all the parts with PCTG. Geänderte und verwendete Dinge aus: Changed and used things from: Adjustable LED Strip Backets https://www.thingiverse.com/thing:2207879 40mm Fan turbine cover with Dust Filter ...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use.It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...