3d printing stringing test

Thin "windows" are designed into the forward and bottom surfaces of the backpack, which can be cut away after printing to increase much-needed airflow. PRO-TIP: The DTX03 ships in standard-definition mode, but it's capable of recording nicer video...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

*Printed and checked. Passes XYZ Calibration and Selftest.* **Credits:** --------------- 1) Inspired by the MGN12 Linear Rails designed by Stwebster (https://www.thingiverse.com/thing:3400952) 2) Y-Tensioner and Z-Motor_Mounts are modified...

For screws, you can use either two nuts per leg (one above and one below the printed hole) or M3 threaded inserts. I designed the screw holes tightly so that M3 screws alone are usable, but be aware that adjusting the screws multiple times will...

There are a few different files here: Fairmile D MGB Early - the boat as it was originally made (guns, apart from the two twin 50 cal mounts, printed separately) Fairmile D MGB - the same boat with a raised platform added amidships for mounting 20mm...

This is a remix of the smart nanoleaf replica from Surrbradl08 wich can be found here: https://www.thingiverse.com/thing:3354082 The SMART CIRCLE LED DOT is easy to print. I use black PLA for the top, the bottom and the inlet. For the diffuser i used...

https://www.thingiverse.com/thing:3107686 Ich habe diesen Laserkopf von Cloudray:...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

Print one and check for fit. Make micro adjustments in the X & Y axis of your slicer if the rod cap is too tight or too loose. There are Left & Right 3MF file versions with built-in supports. There are also STL versions with supports if you prefer...

You may also request this model printed and assembled with velcro at https://jkl-adapters.com/   Description To solve the tracking issues experienced by penholders while playing Eleven Table Tennis on the Oculus Quest 2, I created a series of penhold...

I printed the waterwheel with an SLA printer because it is easier to get a smooth axle and a balanced waterwheel. The wheel runs slower if it is mounted the wrong way round. So the water runs onto the underside of the blades. I kept the bottom of...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

upload My modified MKS firmware for mks robin nano (fork mks v2.0.2): https://github.com/ochkariky/MKS-Robin-Nano-Firmware_compile (add More menu, M48, add UBL support in autolevel menu, increase length name in Print menu.) Resolves the issue of a...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...

Since publishing the Filament Server System in 2013, I've sought a more efficient system requiring less printing, fewer loose parts, easier assembly, and simpler spool changeovers. When creating the pipe-based, wall-mounted Spool Storage Rack last...

The print itself is only a case and a lid, but I thought it may inspire some other creative invention. I apologize for the poor quality of the video and my gross fingers. It was really hard to get the camera to recognize the led screen because of...

The pieces can be assembled in multiple different ways.  - Alien Desert bases: 19 different bases ranging from 30mm to 80mm, and including a desert rock scenery piece.  All the parts are pre-supported for SLA resin printing! Storyline of the...

Make a print on dark material, preferably black. RESUMO Tampa PET para iscas de abelhas jataí e mirim - abelhas sem ferrão v1.0 Esta tampa visa facilitar o preparo de iscas para “abelhas nativas sem ferrão” (tribo Meliponini), o tamanho...

Plug in to your pi, then expand your file system using "sudo raspi-config" There are a few ways to access your print server. Find out your RPi ip address, then type it on your browser http://printrbot.local/ My image has avahi installed, which...

They print at slightly hotter temperatures. Also, consider flexible TPU filament for the lid bumpers and the washers. The resilient material offers a quieter closure on the lid, and gives a bit of conformance on the nut tightening. The bumpers...

I was thinking of printing JT3D's Affordable Rock Tumbler but wanted a little more control so I decided to build one based on an Arduino. The main thing is the stepper motor and using its rpm and steps/revolution to get an approximation for how long...

You'll also need a 2, 3, and 4 mm drill bit to clean out the holes unless your printer prints perfect holes. Drill out the holes carefully; I used my fingers for the 2 mm holes on the case. Use the Bed Triangle part to mark the two holes to drill in...

Printed in PETG with .2mm layer height. PETG is recommended if you're going to put this in your aquarium. The more infill you use, the less buoyant the rack will be in the water, also depending on the wall thickness you use. The provided Suction...

For this project, you will need: • 1/8" Clear acrylic • 1/8" white acrylic • Spray paint • Methylene Chloride Cord or chain Print Settings Printer: Trotec Speedy 300 How I Designed This Step 1: Laying out the letters To produce a high-quality...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

You reuse the axles and bearings that came with your MMU2 kit.Print instructionsTo mount, push the end of the bowden tube from the back of the MMU into the hole on the end of the "Frame". Move the "Frame" on the wall so the tube has a graceful curve...

... a piece on the bottom to prevent the gap on that side. Hopefully it won't interfere with putting the cable in too much. Update: I goofed on the previous one, and forgot to include a hole for the power cable, so now I'll have to print a third time.

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

I've included them as the "Corrected" fins but left the original in case you want to print the slightly oversized ones for extra stability.\r\n\r\n5) You'll need the nose cone linked above (I used the "Base2" base for this nose) and the retainer...