3dr pixhawk 2

Pixhawk is an advanced autopilot system designed by the PX4 open-hardware project and manufactured by 3D Robotics.

Thanks :-) Today I tried to design the replacement Shell for 3DR-Pixhawk. For the first time, I opened my 3 years old Pixhawk, just to look inside, and got an idea to design its case. If there is an error somewhere in the measurement, please let...

Upgraded version of https://grabcad.com/library/pixhawk-2-1Added exported version to other formats, exports made in Fusion 360.

Works with this GPS: 3DR uBlox GPS with Compass Kit https://store.3drobotics.com/products/3dr-gps-ublox-with-compass PIXHAWK GPS MAST F450 Very strong foldable I have used a brass screw for the GPS socket (non metallic) (4 x 5/8) And Zinc Plated...

Works with this GPS: 3DR uBlox GPS with Compass Kit https://store.3drobotics.com/products/3dr-gps-ublox-with-compass PIXHAWK GPS MAST F450 Very strong foldable I have used a brass screw for the GPS socket (non metallic) (4 x 5/8) And Zinc Plated...

Anti vibration mount for the Pixhawk flight controller available from 3D Robotics. Edit: Thanks to Radiocontronics, I've added a new version of the bottom plate with 52mm x 52mm spacing to suit the Tarot T810. ... ...

A simple Pixhawk 2 mount. ...a Pixhawk 2 will snap right into the teeth, and you can add vibration dampeners (like found on DJI gimbals) to the holes and then add those to your frame to keep the Pixhawk safe.

Dimensionally accurate model of the ProfiCNC Pixhawk 2.1 CUBE with Edison carrier board

Trying to add a mount for the Pixhawk to the Crossfire 2. The only problem is their are no native files for the onmimac mounts. I have converted the pixhawk mount from STL to SKP; but in the end there were little holes in it that netfabb couldnt...

8mm for power switch 3mm for nut

Pixhawk PX4 2.4.8 A Controller for RC Aircrafts.

For mounting the pixhawk to the crossfire 2 using MikeyBs original design. just tweaked for the layout for the pixhawk. ...Works Perfect.

Based on the pixhawk and through smart design, the bill of materials has been reduced which keeps the overall design simple, affordable and extremely light at only 75 grams per board.More info here:...

Autopilot Pixhawk Boardhttps://pixhawk.org/_detail/modules/pixhawk.jpg?id=modules%3Apixhawk

So I was getting to mounting my Pixhawk 2 to my new frame and noticed the cube is off-center on the carrier board. I created this model for you guys to print. ...It has the cube centered with the four inner holes, and has the drilling portions marked.

This is the model of Pixhawk autopilot

EDIT [3/11/2015]: A larger multi-purpose case is here - http://www.thingiverse.com/thing:719615 Changes for the v.2 3DR Radio are a smaller connector gap and the case is slightly longer. This case extends beyond the base of the antenna connector to...

EDIT [3/11/2015]: A larger multi-purpose case is here - http://www.thingiverse.com/thing:719615 Changes for the v.2 3DR Radio are a smaller connector gap and the case is slightly longer. This case extends beyond the base of the antenna connector...

With this mounting plate you can easily add a Pixhawk 2 to your Tarot 650 Sport drone.

Mount for the 3DR airspeed sensor. Instructions Print at 45°, so that the seam between top and bottom parts is level with the print bed. Use the included template to cut a ~10mm recess into wing or...

Aesthetic Model (Basic Structure)1:1 Scalehttps://www.3dxr.co.uk/product/pixhawk-2-1-standard-suite/

Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable.

This mount adapter allows for the installation of a Pixhawk 2.1 to a 45mm square hole pattern found in many large scale multirotors. Make sure to attach the standoffs prior to screwing down the Pixhawk 2.1 due to the fact that the PH2.1 covers the...

I have seen many printable upgrades for the fpv raptor v2 2m span here but I need this special one in order to put the pixhawk 2 inside the fuselage. You will also need to cut the upper plastic square section (see images) in order to install it...

vibration dampening mount for pixhawk and 3dr gps module Print Settings Printer Brand: RepRap Printer: hictop prusa i3 Rafts: No Supports: Yes Resolution: .2 mm Infill: 20

bazır pixhawk

Pitot Pixhawk

Pixhawk mount

pixhawk 5 base + cube

electronic component used for controlling