3m command tape 3d models

Cable hook designed for use with the small 3M Command Strips. ... For the greatest strength, I recommend printing on its side with a brim for stability.

This is a mount to attach a drone to your wall without using nails It uses a 3M Command sticky hook mount (https://command.3m.co.uk/3M/en_GB/command-gb/products/~/Command-Medium-Utility-Hook-Value-Pack-17001-6) - all you need is the adhesive pad and...

Picture hanger that works with Ikea Ribba or any other frame that has a similar mount. ...Uses two large 3M Command strips to safely secure the picture to the wall.  Printed in PLA with default settings.

Conceived to effortlessly hang from a 3M command hook on a desk or wall, this innovative printer breaks free from conventional constraints. ...Capable of producing high-quality prints without the need for cumbersome support structures.

I needed a screwless blind cleat that would work with my existing 3M Command strips. ...Building on evolseven's design, I learned FreeCAD and adapted it to meet my specific requirements.

I needed to attach my MMU to something, and I wanted to use 3M command Picture Hanging Strips. ...I modified two of the original support struts to have a flat surface between them.

Needed a broom holder. ...Found the design that fits, by MadeByEvan, but I didn't want to drill any holes in my cupboard. So, remixed the design to have larger surface area to put 2 large 3M command strips.

This cable clip is designed to with the smaller 3M Command Strips. ... For the best strength, I recommend standing the clip on it's side (as pictured), and using a brim for stability.

I needed to attach my MMU to something, and I wanted to use 3M command Picture Hanging Strips. ...I modified two of the original support struts to have a flat surface between them.</p>

... objects (i.e. headphones) to be used. Best bet is to print this hook on it's side and use supports for the ridge in the back. https://www.command.com/3M/en_US/command/products/~/Command-Large-Utility-Hook/?N=5924736+3294529207+3294773688&rt=rud

You can find those strips on Amazon here: https://www.amazon.com/Command-Picture-Hanging-Strips-8-Strips/dp/B00SFWNAFC/ref=sr_1_5 or here: https://www.amazon.de/Command-17202-3M-Bilder-Montagestreifen-klein/dp/B00016ZLDY. Printer Settings: I use my...

This is a sturdy wall hook that utilizes two large 3M Command Strips, each designed to support up to 5 pounds of weight. By using two strips in tandem, the combined holding capacity should reach a substantial 10 pounds. As I put this system to the...

... with one thing in mind: strength. The medium Command Strips can supposedly hold up to 3 pounds of weight, but I'm confident that this revised hook will easily exceed those limits - at least until the adhesive gives way at the 3M Command Strip end.

Sign Clip for use with medium 3M Command Adhesive Strips. Holds up to two signs against a flat surface. Tested for six months in a healthcare setting with 24/7 use. ... Great for holding precaution signs on glass doors, especially when the sign can...

... the wall, the hook itself slides over and snaps into place on it, hiding the lug and the adhesive strip underneath. Designed specifically for use with 3M Command strips (use the largest size that will fit completely under the wall side of the lug).

A simple wall mount hook designed to fit the profile of a 3M Command Adhesive Strip (Large). Currently using a bunch of them to hold hats on my wall. ... I suggest printing on the side with no support and 15% infill.

... and found a pretty decent one on here but I thought I'd detail it up a bit. ...Rawr! Using a 3M command strip to attach it to the wall. ... Intended for resin printing but with the right settings and supports I'm sure it could be printed on an FDM.

... collar diameter is 10mm. Designed to be 'renter friendly' using 3M Command strips (Large 2.2kg type). ... Print Settings: Printer Brand: MakerBot Printer: MakerBot Replicator 2X Rafts: No Supports: No Resolution: .3 Infill: 30% Notes: 3 skins

... really soft and you can then press it to the surface you want to mount. I didn't find that it was too hot to touch, but obviously be careful. After it cools for about 30 seconds the print becomes ridged again and you can apply the 3M Command Strip.

... really soft and you can then press it to the surface you want to mount. I didn't find that it was too hot to touch, but obviously be careful. After it cools for about 30 seconds the print becomes ridged again and you can apply the 3M Command Strip.

This wall hook is designed to be used with the large 3M Command Strips. You just apply the Command Strip to the narrower face of the Wall Plate, apply to the wall, and slide the hook over to the plate while keeping the pull tab hidden. I added...

This innovative design pairs perfectly with the basic wall hook, specifically engineered to work seamlessly with 3M command strips. The visually striking jet fighter decorative piece doubles as a clever solution for hanging lunch boxes, though it's...

The wall hook is designed to work with 3M command strips. The decorative part is a jet fighter, we use it for hanging lunch boxes, but could be used for anything that the command strips could hold up. If you want to create your own decorative...

I designed this to work best with the large 3M Command strips, the ones that are rated to 5 lbs, however it also works just as well with the medium Command strips, too, for smaller pictures. I've hung many framed pictures throughout the house...

... days off with ink on their sheets. I was annoyed by finding markers in the bed every day, so I created this solution to keep them safe and secure. The flat design fits perfectly with a 3M Command Strip, which doesn't damage walls when removed.

This is a wall hook that can be put up with a 3M Command Strip similar to the thing: http://www.thingiverse.com/thing:221562 but I redesigned it so that it was a bit thicker, had a longer hook and had a groove down the side. The groove is intend to...

This is designed for the “Poster” size 3M command strips, part number PH024-64NA,e.g. ...<a...

Here are the features that distinguish this wall hook from others like it: First, the 3M Command Strip holds it firmly in place. Similar to a product found on Thingiverse at http://www.thingiverse.com/thing:221562, but this redesign adds a thicker...

Just a couple small changes on the original design: * I made the base the size of a 3M Command strip to maximise adhesive usage. * I oriented it for printing on the side so layer adhesion isn't relied on for holding up the Kitchen Aid accessory. ...

So, I created a simple bracket that fits into the keyholes on the back, and is the right size for one large 3M Command Strip to hang it to the wall. ...You can affix the plate to the wall, then mount the duck head onto it exactly like you would if you...