3mm barb fitting 3d models
446830 3d models found related to 3mm barb fitting.grabcad
Stainless Steel 1/2 inch Barb to 10 mm Hose Connection , 304 or 316, water or steam.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: output_units = Metric connector_type = inline input_barb_count = 4 input_units = Metric input_size = 3 inline_junction_type = round...
thingiverse
... screwed it into the compressor. The compressor gets warm and softened the PLA print. I had to support the air hose so it did not put a force on this fitting when it was warm, used it for 3 days in a row so far no leaks. ...use at your own risk :-)
pinshape
... screwed it into the compressor. The compressor gets warm and softened the PLA print. I had to support the air hose so it did not put a force on this fitting when it was warm, used it for 3 days in a row so far no leaks. ...use at your own risk :-)
cults3d
... it into the compressor. The compressor gets warm and softened the PLA print. I had to support the air hose so it did not put a force on this fitting when it was warm, used it for 3 days in a row so far no leaks. ... use at your own risk :-)
thingiverse
Print settings: For the barb fitting I printed standing up with the thread side up Used supports for touching the build plate only printed at 0.2 resolution with 45% infill 3 walls For printing the nut I increased the size of the part to 102%...
thingiverse
1/2 inch BSP thread barb fitting to fit 12 mm diameter pipe
thingiverse
This is a 0.2" ID 4-way barb fitting used for 1/4" (6mm) hose.
thingiverse
This is a 0.2" ID 5-way barb fitting designed to fit 1/4" (6mm) ID hose.
thingiverse
This is a 0.2" ID 3-way Barb Fitting for most 1/4" (6mm) ID Hose
cgtrader
This is a model of a barb fitting for PC water cooling, with G1/4'' thread. For use with 1/2'' internal diameter tubing. Useful for planning and rendering custom PC builds or mods. Dimensions measured from the real product. ...
thingiverse
This design contains: - the barb fitting (rounded or with a hexagonal face) - a nut to screw on from the outside - rings to be used as seals - a wrench for the hexagonal fittings I created this design to get rid of waste water from my countertop...
thingiverse
Barb fitting for a TotalPond 140 GPH Fountain Pump model # 52217 The barb fits 3/8" ID hose The lower portion fit's into the 13mm hole on the fountain pump. ... Printed standing straight up, I used supports around the bit of overhang around the base of...
thingiverse
This is a fitting for a water pump requiring 1/2 FNPT to 1/2 ID tubing barb. ...Modified for 3d printing no supports.
thingiverse
This is a hose barb fitting I made to use with the turbo boost controller in my car. The threads are 1/8" NPT and the hose barb is approximately for 5/16" rubber vacuum hose I think. Should work with 1/4" too I guess. ... ...
grabcad
Brass hose fitting for 3/8" ID hose. ...Ferrules on barb end hold hose from slipping off. Use of hose clamp helps prevent leaks. 1/2" Male NPT thread on opp end. ...7/8" hex
thingiverse
simple easy to print , 1/8 bsp to 10mm tube barb , 90 degree fitting . ... I use an npt die and tap to finish both sides so the fitting has the taper on it l, it will seal in a tight enough fit .
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: vault_support = yes connector_type = inline input_units = Metric inputs = 1 vault_connector_ratio = 1.8 strength = 1.0 output_barb_count = 4...
thingiverse
Barb Fitting G1/4" a 3/8" for Custom Watercooling The design was made in Fusion 360. I used PLA + and then gave it a layer of UHU Expanded Polystyrene to prevent any leakage in the piece. ... HOSE USED: - Diameter: 3/8 "(9.5mm); - Thickness (wall):...
prusaprinters
Print it barb side up.The barb is 13 mm at the narrowest and 15.6 mm at the thickest, works perfectly for ½" PVC tubing, though getting it off can be tough.
thingiverse
I needed replacements for broken original pipe fittings that go into the Hot Tub heater. (240V6KW SSE-00-OH-OF 19400 0034 Watkins MFG Corp) Could not find anything that would fit. This was neither 3/4 nor 1 inch hose barb. So I decided to print...
thingiverse
I designed a single-barb adapter and a 3-barb adapter. I included a solid and and hollow version. The solid version may be useful if you want to drill a single diameter hole through the adapter. I usually have to scale by 10 all my drawings when...