450 rc helicopter 3d models
38516 3d models found related to 450 rc helicopter.thingiverse
... helicopter. ...I think this design should fit most 450 size ones as the designs are almost identical at the bottom. Nice bit of flex to the parts (using ABS) to give a nice soft landing. ... These give the helicopter a 5 degree pitch forward.
grabcad
An incomplete, but nice looking model of my Hobby King Align 450 clone, originally made in Alibre Design and finalised in SolidWorks. Most of the important parts including full metal head and tail are there. ...Decals for rotor blades and canopy...
thingiverse
This is a rotor blade for a T-Rex 450 RC Helicopter optimized for very stable flight. The lightweight rotors provide much better stability over stock rotor blades. You can print this with supports which creates a very rigid blade preventing flapping,...
thingiverse
Please be extremely careful when flying helicopters! This is not a quadcopter, blade strike may cause a serious injury! Do not fly this thing with people around! The printed rotor head or entire transmission frame may blow up in a case of linkage...
thingiverse
After a recent crash, I decided to make a new fin for my KDS450SV. ...Nothing fancy, just functional.
thingiverse
After a recent crash I noticed that the gyro on my KDS450SV is a bit exposed, so made a small cover thats tough enough to take a flyer strike in the event of a crash.
youmagine
I was looking for a nice solution to mount the antenna in to the 90° angle.The Piece can be pushed to the landing and holts already firm in my case.
thingiverse
fits align / hk 450 solidworks file included for easy customization the hole will probably be tight. ...you should pass it with a 5mm drill and put some wd40 or other lube inside or you will have a hard time removing it from the shaft
thingiverse
I remixed this to rotate the hole pattern 90 degrees as the motor I was using has the cable exit in the opposite corner. ...Great design to use.
thingiverse
Custom design 450 class RC helicopter. Designed to use align components from any 450 class bird. Recess in side frame is designed to fit the Tarot zxy FBL controller. I have assembled this model and can verify fit. It has yet to be flown as I am...
grabcad
Transmitter: 6CH RTF/ARF RC Helicopter3. Length: 25.8in (655mm)4. Main Rotor Diameter: 28.3in (720mm)5. Tail Rotor Dianeter: 5.3in (135mm)6. Gross Weight: RTF with li-po battery(670g)7. Battery: 11.1V 2200mAh 15C li-polymer8. Motor: Brushless...
thingiverse
A simple battery try to firmly locate the lip at the front of my KDS450 SV. ...Attaches to the existing mounts on the fram.
thingiverse
Update: I have realised that the PLA is great for avoid damage in helicopter crashes (I have had several last days ;) ). ...PLA main gears acts as a mechanical fuse better than standard gear (ABS), in a crash teeth break apart quickly and avoid damage...
thingiverse
i have looked and looked for a 3D printable version of the guns on Airwolf and could not find them anywhere plenty of pictures but no files to download so i created these in SOLIDWORKS i hope you guys like them i have also included the Solidworks...
thingiverse
Properties: z = 140, step = 0,5mm Fully functional part.
grabcad
Some renderings I made using KeyShot 4. ...The model (HK-450 RC Helicopter) is made by GrabCAD'er Steen Winther. ...
grabcad
The model (HK-450 RC Helicopter) is made by GrabCAD'er Steen Winther. I made these renders to explore all the capabilities of Autodesk Showcase. Although it's pretty basic software, you can create quite good results with it IMO. If you like these...
thingiverse
This is a work in progress and used to create a mould for a 450 fibreglass fuselage for a RC helicopter. ...You could easily print it an use it that way, or use the split the moulds to mould your own. Designed around a flywing H1 450 RC Helicopter.
pinshape
I liked how my 250 helicopter blade holder came out, so I decided to make one for the 450 size helicopter. ...This fits a 12mm boom.
thingiverse
These fins are sized to fit Trex 450 style helicopter tails. Check back for more styles and other sizes in my things list. I'm using .8mm walls with 17% triangle infill, makes it very light and reasonably strong. Here is my goto PLA brand: ...
cults3d
These fins are sized to fit Trex 450 style helicopter tails. Check back for more styles and other sizes in my things list. I'm using .8mm walls with 17% triangle infill, makes it very light and reasonably strong. Here is my goto PLA...
thingiverse
Fuselages for Align Trex 450. download Files. ...www.heliprinted.com Print it anytime you need.
thingiverse
This is a gyro platform for T-Rex 450 V2 frame. The original part is just a bit to small and the wiring comes to close to the gears that drive the belt. ...This platform is big enough for most of the flybarless systems and the position of the gyro is...