5 axis maker 3d models

After the installation of linear rails on my ender 5, the y-axis belt fixation on the gantry sits a lot higher above the 2020 profile. Because of this, the tension becomes higher when approaching the sides of the bed because the gantry gets more...

I've compared it to the MK2.5 Carriage of the Bear X-Axis v0.6 and noticed some minor differences in the alignment of the Cable Bundle and Endstop Trigger. This could cause the cable bundle to collide with the frame or electronics housing and...

I've compared it to the MK2.5 Carriage of the Bear X-Axis v0.6 and noticed some small differences in the aligning of the Cable Bundle and Endstop Trigger. This could make the cable bundle colliding with the frame or electronics housing and prevent...

On my first Shapeoko 5 Pro print, I crushed my right-hand Y axis drag chain mount by crashing the Sweepy (that I had set to the 4:30 o'clock position instead of 6 o'clock) into it while zeroing a bit. This is a (close enough) matching part that fits...

Z-axis trigger position indicator for flying bear ghost 5 printer. The product is mounted on top of the standard plastic handle on the trigger of the z-min sensor. This simple device allows you to adjust the Z offset more precisely and allows you to...

Check out: https://www.thingiverse.com/thing:2920060 Designed specifically to work on the Ender 5 print bed, these adapters keep Z-axis cables inside the frame. The bed bracket features a slot for a cable tie, helping to provide strain relief (don't...

I made a simple cover for the X-axis pulley that works on both Ender-3 and Ender-5. This cover is perfect for those who have installed a Motor Damper, just like me. To install it, you only need two small screws and their corresponding nuts. I'm...

This is a comprehensive overhaul of the Z-axis motor and end-stop for the Prusa MK2S/MK2.5/MK3 series. It significantly boosts z-height by 9mm, enhances motor attachment rigidity, and enlarges the area of the z-endstop. This upgrade potentially...

This is a remix of the Rambo Y-Axis mount from https://www.thingiverse.com/thing:398515 This mount will connect up to the Rambo cover that is used in the Prusa 2.5 upgrade kit. This was also remixed from the "Rambo-heatbed-cable-clip.stl" file for...

This new component serves as a substitute for the original Y-axis limit switch holder.

Get a grip on that x-axis belt before it starts grinding away at those rails!

NED axis frame for research / physics orientation

And by assembly process you get: - Excellent orthogonality between XZ plane and XY plane - Excellent orthogonality between X axis motion and Y axis motion. Stuff Tools to go half-way Set of hex drivers. Small flathead screwdriver Supplies to go...

These are custom MK3 style y axis ends for my fresh upgraded Prusa i3 MK2.5. It's super stiff so it won't bend by the tension of the y belt. Best printed in PETG with 20% infill.</p><p>You will need to print the MK3 LCD supports as well in order to...

Done with the cutout profile of a Saturn 5 launch (second picture is reference) Also added a lunar lander and module from https://www.thingiverse.com/thing:3758364 for a nice touch (scaled at 130%) Print Settings Printer Brand: Creality Printer: ...

Relocating endstops for X- and Y-Axis on Creality3D Ender 5 requires extreme caution to avoid damaging your printer. DO NOT, under any circumstances, use auto home until you've completed this process correctly. First, disable steppers or turn off...

The only issue was that the Z-Axis Spindle Bearing holder was about 10mm too short for my specific needs. Since I had a different sized bearing, an MBB81235 measuring 12x8x3.5, I needed to make some adjustments. My CTC Dual printer requires precise...

ENDER 3v2 and other models Cover for Z axis stepper motor. ... Ive added a dual Z axis setup on my E3V2 so decided with 2 of them they needed covering up!

Heat-set inserts are highly recommended for several reasons. ...They excel at clearing the Z-axis linear rods, especially when working with MGN9 linear rails on the Y-axis.

The other Z axis stabilizers didn't work for me, so I made my own. ...I use 608 skateboard bearings.

Since Folgertech is now selling the R2 model, they have made available parts for the new model, including the long belt and idler pulleys for the Z axis. Belt here: https://folgertech.com/collections/beltandpulleys/products/987-gt2-6mm-belt-loop ...

I needed just a 2mm extension because for some reason my y-axis was grounding out further into the build area than the designed parameter.

Copy of the original X-axis sensor stop mount that also mounts to the stepper motor. ...I am modifying this for a camera mount

Parametric Gear with 30 teeth and 25 mm axis I can design any other gear part with custom dimension. ...Just ask me for it

These custom MK3 style y-axis ends have been designed specifically for my upgraded Prusa i3 MK2.5, boasting super stiff construction that resists bending under the tension of the y belt. For optimal results, it's highly recommended to print these...

I designed these clips to enhance the Z axis tensioner's ability to prevent table drop when the steppers are turned off on my Ender 5. They closely resemble bowden clips used on extruders and hot ends, but with a few key differences. These clips are...

Quick and dirty update to the cable chain tray for the X axis. ...Allows the trays to be used without the need to relocate the Y endstop. This replaces the right-hand (from front of printer) piece of the X axis tray.

The main design came from here: Ender 5 X axis stepper cable guide by cavac https://www.thingiverse.com/thing:4371316 I used the graphics from here: Creality Ender-3 Logo by tom666 https://www.thingiverse.com/thing:3078936 The Rounded cube module I...

... Lastly, put smooth rod belt pulleys onto the smooth rod, which can move freely. A video is available for visual guidance, and a z-axis wobble arrester should be fitted to the opposing diagonal threaded axis (http://www.thingiverse.com/thing:3057).

Just a little cap to cover the Y axis switch pcb when using D_Jespersen's belt covers.  I printed it upright because it's a small enough space to bridge. ... Snapped right on, first try.