8mm rod clamp 3d models
147996 3d models found related to 8mm rod clamp.thingiverse
I wanted a simple and easy clamp to hold my spool onto an 8mm threaded rod. I didn't like any of the other clamps I saw so I made my own. ...It has a 7.75mm center hole so that it can clamp onto the 8mm rod well.
thingiverse
Not sure of correct name for these but its for mounting 8mm rod. It accepts 3mm cap head bolts and traps a nut for clamping. ...
thingiverse
A simple clamp for 8mm smooth rods hardware needed per clamp: 1 x m3 x 8mm bolt 1 x m3 nut Print Settings Printer Brand: RepRap Printer: P3Steel Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.26 Infill: 80% or more
prusaprinters
A simple clamp for 8mm smooth rods hardware needed per clamp: 1 x m3 x 8mm bolt 1 x m3 nut Print Settings Printer Brand: RepRap Printer: P3SteelRafts: Doesn't Matter Supports: Doesn't MatterResolution: 0.26 Infill: 80% or more Category: 3D...
cults3d
... new rods were a bit too long, and I didn't have any way to cut them down to size. ...I put these clamps together as a way to keep the rods in place, and to remove a little bit of wobble that was due to the Anet rod holes being just slightly too large.
thingiverse
... new rods were a bit too long, and I didn't have any way to cut them down to size. ...I put these clamps together as a way to keep the rods in place, and to remove a little bit of wobble that was due to the Anet rod holes being just slightly too large.
pinshape
One of the smooth rod slid out a little bit when I tried to print something with 50mm/s because there are no rod clamp to stop the smooth rod from being slid out due to the fast carriage movement This uses m3 bolt and nuts Instructions Print this...
thingiverse
One of the smooth rod slid out a little bit when I tried to print something with 50mm/s because there are no rod clamp to stop the smooth rod from being slid out due to the fast carriage movement This uses m3 bolt and nuts Instructions Print this...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2125220 Instructions Using the following options: rod_diameter = 8 bolt_diameter = 3 nut_thickness = 2.4 nut_diameter = 5.5 rod_margin = 3
thingiverse
I made these to compensate for smooth rods sitting in fixtures that had oversize holes or holes that got reamed too large either intentionally or in error. If you use any other size rod, it's simple enough to scale this up or down. Primarily used...
thingiverse
8mm Linear Rod Clamp, 15mm aluminum extrusion. Use m3 screws to secure. Tolerance is tight on this (8.1mm diameter) Drill your hole with an 8mm drill bit if your rod does not fit. The rods should fit snugly. This thing was made with...
thingiverse
Customized version of https://www.thingiverse.com/thing:2125216 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2125216
thingiverse
Clamps onto rod and can be secured (if needed) with tywrap. Remix of https://www.thingiverse.com/thing:2932583, added holes for mounting screws and tywrap slot. Added lines to end of Openscad source (attached) to subtract holes and slot. Printed...
thingiverse
Simple 8mm Rod Clamp for use as bushing / end-stop or use with thrust bearing. Interior is NOT threaded so can be easily moved and adjusted on rod. Models (all for 8mm rod): + Single (10mm) + Double (20mm) + Single (10mm) w/ACME Threads 2mm pitch...
thingiverse
I recommend using some blue tac or similar in the middle to make sure it is getting a really tight grip, though it is not necessary it will help This makes it easier to clamp a round rod in a vice made for rectangular objects, I have used it several...
thingiverse
Klemmenbolzen.stl with brim Klemmenhebel.stl with support Print Settings Printer: SparkCube Rafts: Yes ...
thingiverse
This is a clamp for a 8mm smooth rod onto a 2020 bar, using M3 screws. I was able to get it to hold to the nuts using a 12mm screw. It holds very tightly, and straight. ...I used it to add smooth rods to a CR10S for a better Y-axis.
thingiverse
This is a replacement for the zip ties that come with a QU-BD one-up & two-up that actually holds the rod in place. ... I recommend using shorter bolts then the photo shows.
thingiverse
This is the front extruder carriage for Jon Lawrence's 300mm No sag Y extension for the printrbot Simple 2013-2014 http://www.thingiverse.com/thing:242185 This version has a clamp that attaches to the upper 8mm pole and then using a m3 nut and bolt,...
myminifactory
These are flex material printed 8MM rod mounts. they assist is helping to dampening the noise of the Y bed movement on most i3 type printers with a 2020 frame setup as well as possibly on other frames with 2020 extrusions.Obviously the yellow is flex...
thingiverse
By clamping down the rods, you will be able to tighten the GT belt much tighter. Without damaging the X-ends and also keeps from bending your X-Axis rods. You will need to print two, each placed against the left and right X-ends. If you want to...
prusaprinters
I'll include this as well if it will help anyone, its just a block with a 6mm hole for a 1/4 29 bolt. I'm sure there is a more elegant solution out there but I made this one (isn't that the point?). Threads m5 socket head screws on the clamp side...
thingiverse
... out there but I made this one (isn't that the point?). Threads m5 socket head screws on the clamp side once taped (one way or another) Note: I made this for my rather old, DIY reprap i2, so I couldn't say if it will work with other printers.
thingiverse
Clamp for 8mm rod The original i found here was 10mm. So I made an adapter first. Then modified/remixed it. Remix of a thing i can not find anymore. ...Sorry Props for the original designer.
thingiverse
Recently, the vibrations of the table guide rods have been noted. ...Design small elements that perfectly eliminate the vibrations of rods. ...I post, someone can use the in their Anet printer.
thingiverse
This is a simple clamp for an 8mm rod. ...I use it to hold a spooler on top of a prusa wood frame.
thingiverse
I designed those clamps to mount a newspaper basket ("Blomus 68477 Wires Newspaper Collector") consisting of 8mm chrome-plated rods to an old chopping board with wheels. I wasn't reading the newspaper on paper anymore and the chopping board would...
thingiverse
Simple clamp bracket for holding 2 8mm carbon fibre rods ( normally they're undersized, designed for 7.8mm ) at right angles to each other with a 14 mm offset. Uses 4 M3x12mm oval head bolts and associated nuts. (M3x10 also fits, but only just). ... ...