8x10 clip frame 3d models

This is a picture frame for 8x10 pictures, inspired by the design available at http://www.thingiverse.com/thing:251944. Print the plate along with the center and two of each arm, then assemble and attach it to the wall using screws. Personalize your...

Oval embroidery frame. Size: 8 cm x 10 cm useful diameter for embroidery (internal size). My nets: https://www.instagram.com/piramide.3dlab/ If you liked my work and want to thank, you can mention me in networks, with that simple gesture I can...

Customized version of https://www.thingiverse.com/thing:251944 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=251944

... ...Area inside the frame fits an 8x10-ratio picture. Picture is held in place by a small ledge. Prints fine without supports in default orientation, but the inner edge of the top part of the frame may droop a bit because it's bridging rather far.

Customized version of https://www.thingiverse.com/thing:251944 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=251944

The clips run into the edges of these binder clips when you try to attach them. Consequently, you're only able to clip down two sides because the other edges stick out. I've designed a solution by crafting specialized clips that extend beyond the...

And you can only clip down two edges, because the other two edges stickway out. So I've designed these clips that fit on the corners of the print bed, extending it so that it holds standard 8x10 plate glass. The edges of the clips are thin, so you...

A raised frame clip for extra think art. ... Why? My wife wanted to frame a small blanket, and the previous clips could not hold the blanket and backing in place Design: https://www.tinkercad.com/things/eEWLlLNJEqu

Introducing our 3D printed frame clip, designed to securely hold a sheet of paper or other thin material to a frame. This clip is easy to use and ensures that your artwork stays in place, making it the perfect solution for displaying your favorite...

This the small clip that hold a sign in the Frame used primarily by real estate signs. ... I went with 100% infill to make it as strong as possible since it does need to be snapped in place.

Customized version of https://www.thingiverse.com/thing:2718464 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2718464

Customized version of https://www.thingiverse.com/thing:2718464 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2718464

The Human factor has long been a driving force behind innovation and progress. Humans have consistently demonstrated an unparalleled ability to adapt, innovate, and push beyond the boundaries of what is thought possible. This innate capacity for...

Customized version of https://www.thingiverse.com/thing:251944 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=251944

Add a glass bed to your CTC, Makerbot, or Flashforge 3D printer using picture frame glass that is exactly 2mm thick. Be prepared to glue a small shim in place since it's not uncommon for glass plates to be cut slightly off square on one edge. ...Once...

These clips fit seamlessly onto the 8x10 glass bed, snapping securely into position and feeling remarkably sturdy. ...Simply slide them sideways to effortlessly remove them.

Created a personalized photo frame, necessitating clips for securing the rear panel. ...The clips accommodate a #4 screw for an efficient attachment.

A clip that fits on the RigidBot frame and holds one wire with some wiggle room. Edit: Fixed the scaling. ...Should be good now.

I designed this clip to secure polycarb sheets within a shade cloth frame after their expiration date. Removing it once clipped in proves challenging, but it holds securely when using multiple clips. I printed the clip in PLA, anticipating that...

Simply print the clip, attach it to the back of the frame with super glue, and hook onto the nail. For best results, make sure the back of the frame is recessed into the border so it sits flush after installation. The clip is 0.150 inches thick,...

3 versions: normal, doublesided one side, second side is flat to not hit the extruder while working (on some printers) and one without frame clip for double-sided glue tape Printed with 0.4mm nozzle and 0.1 and 0.2mm layer height. ... You may need to...

... more challenging to detach. I suggest utilizing the V1 clip if you plan on frequently removing and reapplying the device. There are already numerous clips available for 2020 frames, yet most do not provide a flat surface for mounting other devices.

I took the clip from thing:4636337 and the ledstip holder from thing:225216 and combined them to create this 18cm led strip clip-on for a 2020 frame I made this using TinkerCad, and adjusted it so that it can be printed upright without supports.

Assembling a new Anet A8 Plus with an aluminum frame posed a problem: the cable guides on the frame couldn't be properly attached. The cable holders supplied were woefully inadequate, while the cable straps looked less than ideal. Having already...

This is a clip to hold the filament on the frame of the printer for quickly swap filament color. It needs to be printed on the side with support.

This is my custom-made cable frame clip, specifically designed for my trusty Nukeproof Scout 2019. ...It's essential that it's crafted from a flexible material that can stretch just enough during the installation process.

This is to mount objects (christmas stars) on the window frame. This clip is hooked on top of the window. ...A thread can be run through it and down to the object.

I needed to mount a photo frame securely to a wooden board, so I bought a cheap Snap 5x7 frame from Fred Meyer and made these clips. They glue in from the back. Print on the side, requires no supports. ... Category: Decor

Three versions are available: normal, double-sided one side, second side flat to avoid hitting the extruder while working (on certain printers) and one without a frame clip for double-sided glue tape attachment Printed with a 0.4mm nozzle and layer...