Bushing adapter for a Craftsman router 3d models

Therm-a-rest Funnel for air mattress using a Neoair micro pump

... ...(http://www.thingiverse.com/apps/customizer/run?thing_id=65894). For fabrication, specifications include a thickness of 3, a diameter of 34 for d2, and 41 for d1, a character height of 25 (c_ht), heights of 30 for h2 and h1, and 90 for $fn.

This is a complete ring busing assembly designed to fit onto a standard 7-millimeter ring mandrel.

This is for the bed of the Prusa i3 printer. ...Hole spacing is 20mm. These are remixes of http://www.thingiverse.com/thing:57770, which have 30mm hole spacing. !!!!!!!!!!!--UPDATE--!!!!!!!!!!!!!!!!! March 31, 2014 - More space for the screw head.

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...

 I'm including the F 360 model so if you need to make one for your bike/device you can.I modeled the bike part first, then modeled the 34mm cylinder “filler.” Finally, I combined the two using the “filler” as the target and the bike stem model as the...

Looking for a mount to use with your old Sony a-mount glass and the GuerillaBeam you've printed? Look no further! These 3D printable models offer a perfect solution for your needs. I created these mounts because I couldn't find what I was looking...

a USB type A connecter made with 20 gauge solid wire for connecting to a USB port to draw power.the hole is made larger than it should be because my printer cannot make a small hole without being a little poo head.

It's a tool box for a Makita router model RT0700c and its accesories. ...Check the assembly instructions.

Print this design at 100% to be used with the pew-pew project. ...Printed at 150%, it will fit perfectly on a good knight model. To express your appreciation for the design, consider showing your gratitude by sending a tip.

I had bought a magnetic A/C vent clip for my iPhone from Amazon, which was a nice size and design, but the microphone did not have a magnetic bit to hold it in place. This mic holder replaces the magnetic disc on the store-bought clip and provides a...

A case for your Pwnagotchi equipped with a USB-A board to plug into a powerbank. This is not a slim version of Pwnagotchi, on the contrary, it has an additional board on the underside of the rpi. Depending on the tolerances of your printer, the usb...

... discovered an innovative design (located at http://www.thingiverse.com/thing:559977) that caught my attention. After reviewing the design, I decided to remix it in order to create a custom spacer specifically tailored for the LED light on my KLR.

Printer specifications have been set for the Alunar model, which is a high-performance printer known for its reliability and speed. Rafts will not be used during this printing process. Supports also won't be generated to keep the final product...

Print this part at 100% for use with the pew-pew, also print it at 150% to ensure a snug fit on your trusty knight's gear. ...If a genuine desire to express thanks arises, generous tips are forever gratefully accepted.

However, I encountered a problem as the dovetail bracket for the finderscope failed to align with the mounting holes on the NexStar 8. ...Consequently, I designed this custom bracket in OpenSCAD, enabling you to use your NexStar 6SE's finderscope with a...

It's worth noting that the design of this device features a clever space hole where the ice cream can melt without causing a mess, making it easy for users to enjoy their frozen treats without getting their hands dirty. ...A cord or string can be...

... To prevent any water from seeping behind them, apply caulk along the top edge, about half an inch deep. The nameplate faces outward, and the recessed area in the center allows for extra clearance to secure the mounting rod with a 1/4-20 nut.

I crafted this to allow for easy mounting of a Nuvi 6" GPS unit. The trim panel snugly fits into the dashboard cutout from the front side. ...Next, the ball release on the back of the GPS slips seamlessly into its dashboard holder, before being easily...

Tip to be able to adapt the suction cups to break in the valves and put them on a drill. ... Break-in of valves and seats much faster and more efficient!

The enclosure is based on Michd's OpenSCAD design, which offers a customizable OpenSCAD box for PCBs at https://github.com/michd/generic-pcb-box. My enclosure is designed to accommodate an isolated USB to TTL serial with isolated power supply module,...

bushing p2t2

Bushing Model

This is my inaugural attempt at integrating a 5-inch display into an economical FPV system. ...Several revised files have been uploaded; I recently redrafted the mesh structure to optimize printing with minimal supportive material.

People with disabilities face challenges when eating ice cream on a stick, such as Magnum or other similar products, but this device helps them grasp it more firmly and steadily. This design takes note of the fact that there is an open space where...

... heavy use, particularly in terms of chip management. The model I am working with is a Craftsman 13-Surface Planer (Model Number: 351-217430), which can be viewed in detail at http://www.jedidiahstolzfus.com/craftsman-13-surface-planer-351-217430/.

I've included two variants, one with a tighter fit and one with a looser fit. The fit applies to the cable, if your printer struggles with tolerances, just increase the size +1% and it should fit. On my Creality K1 it fit perfectly right away.Print...

... by having it sit on my monitor support rather than being clamped onto my desk. ... big cilinder has an inner radius of 35.2mm and the smaller cilinder has an inner radius of 13mm. The tightening thing at the bottom fits a m2.5 nut and bolt.

therefore, I designed a simple replacement ring, which can be clicked on the binoculars without glue. ...Once in place, the rubber eye pieces can be attached with a little bit of superglue. Instruction: Remove the old eye pieces (they are...

I fabricated a bracket specifically designed to enable me to install an FZ1 tail light on my Yamaha Seca II. While I don't anticipate overwhelming interest in this project, I'm still willing to share it with everyone here. ... The bracket attaches...