Fan Mount used by Droodle for Cobblebot Mod 3d models

In this new design, I raised the top hole by 1mm to avoid collision with certain Arduino models, and lowered the top left arduino mount hole by 0.5mm for a more accurate positioning. ...After printing, verify that all holes are indeed holes, and proceed...

This is a duct for the l9a, that allows you to add 2 * 40x40x20mm fans This screws directly on the l9a, using two of the 25mm screws. Printing: Rotate the model 180 degrees along the x or y axis. ... License: GNU GPLv3

168mm x 26mm fan

A snap in replacement for certain Meanwell power supplies to quiet and tame it with a 60mm fan.

This is just a modified mount that shifts 5mm to the right for this specific thing https://www.thingiverse.com/thing:2833898 , ensuring the circular fan duct aligns as closely as possible with my CTC i3 pro B's nozzle, and preventing fan duct contact...

Cache ventilateur pour l'ajout d'un ventilateur de 60mm sur le vidéoprojecteur Wanbo T2 (max ici). ... --------------------- Fan cover for the addition of a 60mm fan on the Wanbo T2 video projector (max here).

By elevating the fan out of its box, we're given the flexibility to harness the full potential of a 60mm fan. In stark contrast, a standard 40mm fan typically manages a paltry 12 cubic meters per hour. Meanwhile, a 60mm fan boasts an impressive...

Cooling fan modification for DaVinci Mini W. Printing the top and bottom components separately helps prevent excessive or difficult-to-remove support material from building up. ...Note that the fan should blow air directly into the duct, which...

I'm planning to install a 40x40x10mm 5-volt fan, which means I'll need to drill a hole on the side big enough for a USB cable. Then, I can wire the +5v and ground directly to the fan. ...I'll post pictures of it in action once the fan arrives.

A DIY Enthusiast's Delight: Custom Fan Arm Upgrade for Prusa i3 Mk3 B6-B7 Models. This straightforward modification serves strictly as an aesthetic upgrade, streamlining the design to provide a sleeker appearance while maintaining functionality. ...The...

This is a module designed specifically for the 3Novatica Gate 1.0 printer, allowing users to easily integrate a blower fan and an inductive sensor for automatic bed leveling adjustments.

I'm working on updating the Anet A8's extruder fan modification based on the Hadoko design, specifically version two. ...I've recently reinforced the blower mounting system to provide additional stability and support.

... modification. Here is a photo of my modified A8, as I'm using the wiring chain which has a mount in the way. Print Settings: Printer: Modified Anet A8 Rafts: No Supports: No Resolution: 0.1 Infill: 100 Notes: I used PLA material for this print.

Update 1: Version v06 includes a feature that protects the front fan from damage, making it unnecessary to use the metal one. Unfortunately, version v03 didn't work because there wasn't enough space; however, version v06 has fixed this issue...

I designed this RAMPS case originally with a specific goal in mind: mounting two 25mm fans on the side to blow air directly across the stepper drivers, which are then secured to the 8020 extrusion of my Cobblebot Little Monster 3D Printer. Since...

It could probably use a support for the right side of the duct to attach to the fan as it will sag as well on long hot prints.  Printed in PETG, but the ducting is very close to the heater block. ...This has seemed to work pretty well, but...

It could probably use a support for the right side of the duct to attach to the fan as it will sag as well on long hot prints.  Printed in PETG, but the ducting is very close to the heater block. ...This has seemed to work pretty well, but unfortunately...

I've been developing a fan modification that complements the standard fan perfectly and outperforms its predecessor in terms of efficiency. ...To secure the top screws effectively, I suggest drilling a hole at the top for the first two bolts, however,...

Custom Fan Crafted by Hand with Precision

I made this mod to improve the blowing of the printed part and protect the hot end from parasitic cooler flows 12.09.2023 - Added cover stl without K1 logo - COVER_MOD_clean.stl

Remixed from: https://www.thingiverse.com/thing:4703998 Created a new mount to allow using the stock part cooling fan. tkmeki's mount works really well, holds the dual hotend nicely, and makes it possible to print some wonderful things. The only...

I am remixing the clamp from https://www.thingiverse.com/thing:2630027 based on https://www.thingiverse.com/thing:2099577, designed specifically to hold a 40mm fan - I am using a noiseblocker 40mm fan that is both cheap and extremely silent. This...

E3D Volcano Mount for Creality Machines - A Direct Match to Matterhackers E3D V6, but Elevated 8.5mm. ... Get Ready to Harness the Standard Fan from Your Creality Machine to Expertly Cool Your Print Bed Extrusion.

------------------------------------------------------------------------------------------------------------------------ I downloaded and 3D printed a UM2 mount for the E3D Titan(https://www.thingiverse.com/thing:2749539), but couldn't find any...

[will test, edit: dit some warping in a closed environment] ).16 or .20 layer height, no supports needed!I used another tapered screw to compensate for support structures got some design issue's due to the extruder on the ender 5s1 is not centered...

The remix shields the hotend from the fan's airflow.

... an 80mm fan. ...Two files are required: a main one and separate feet for gluing to the bottom. A good fitment is expected. The infill setting can be set at around 35% for this project. ...If proper cooling is implemented, supports won't be necessary.

Inside my ToolkitRC M8 charger the temperature sensor had stopped working, so the fans never turned on (although they used to start up before and were extremely loud). I decided to upgrade the cooling system with a 60mm silent external fan that runs...

This in remix from KP3S v3 adjustable fan mount with bltouch added https://www.thingiverse.com/thing:4951083 My current z_offset: 0.795

For details how to print PSU_Cover_Fan look in the original design (https://www.thingiverse.com/thing:4897394) I have only changed the alignment of the two holes on the side with open end, because they was out of place to screw in the cover...