FlashForge Creator Leveling Feet any MakerBot actually 3d models

Happy to see any kinds of yours testing results! ------------------------------------------REASONS for it------------------------------------------------------ 1. better visibility to the nozzle. 2. Cuter than other 5015 fan mod. (owo)b 3....

... Nut Black Carbon Steel (Pack of 100)" Please give me feedback in the comments. I have made it successfully, but would like to hear of any build issues you may have. ...Crank it out and distribute to those without access to store-bought respirators.

To modify any of the openscad files that use the threading, you will need to download the threads.scad file from http://dkprojects.net/openscad-threads/. The settings for the threads are included in the **ThreadSettings.scad** file, so if you want to...

Now you will be able to see all textures inside your 2d and click on any material name to check out its details. Select a texture by clicking in the panel's left lower right button; next time, open texture from materials list that you already...

The parts are stackable so you can pretty much make any configuration you like. The distributor and cap go on top, run the flexible plastic tubing from the pump up along one of the short corners and join multiple towers as shown in the first picture....

Sort out any problems and make adjustments as necessary before applying glue. Use super glue to secure the base of the bridge. Use a light glue (like a glue stick) to secure the bridge into the slot with the angled side toward the bottom of the...

**Note: This design doesn't have any cell protection built in, so it's recommended to use "protected" 18650 cells.** I also modified the design to take velcro straps, which can be hung sideways or upside down. This version requires more work and...

Success with these blocks: You will need (qty 4) M4 screws, any length between 10mm-20mm. (qty. 4) M4 nuts. (qty 1) 5/8 internal snap ring. Unfortunately, your SC8UU has two internal snap rings, but neither can be used because they are too small for...

Print Settings Supports: Yes Notes: I didn't print the mask from these particular files, but easilyused's print settings should apply: Resolution: Any Rafts: No, used 5mm brim instead Supports: Yes Infill: 100% Post-Printing Loctite Ultra Gel...

Cura supports were also easier to remove.A flat piece of street sweeper brush that I found works well to remove any support material and to clean the glue slot after use.  A piece of 0.032" wire works well to clean the glue distribution...

They also carried 18 bicycles on the deck for the soldiers' use, but I didn't include those.\r\n\r\nThey also sported armor plates on the side of the boat, not at the front or back.\r\n\r\n10 of the boats were modified during construction to become...

Palette or Prusa MMU. No supports or brims needed, but feel free to use any bed adhesion enhancers at your judgement. A couple versions are provided for the star, where it can be included in the silver part, or as separate spokes for a better surface...

I could do other diameters or lengths if there is any interest. The spindle holder attaches to the stock support and uses the stock attachment bolts. The 8mm x 120mm spindle bolt is pressed into the spindle holder and is retained by a ridge on the...

To avoid collision with the x-axis extrusion profile, I shifted my hotends forward by 5mm - your x-axis carriage might need a modification if you experience any issues!\nIf spacing isn't an issue for you, you can use the normal part without the...

Hardened targets like bunkers and fortifications call for the KH.13 Spigot Mortar - a specialized weapon whose gigantic projectiles can reduce nearly any redoubt to rubble. The unique construction of the weapon also minimizes noise and flash, making...

A word of caution: Thanks to its hollow thin wall nature, this is *really* susceptible to any heat. I have seen these warp and deform within 10 minutes in a hot car in the summer! Even Perifractic's one had a slightly warped beak, the parcel...

The Lack Enclosure Drawer unlocks the incredible enhancement of storage for your enclosure in a new and exciting way.*Also works great as an addition to any workbenchFeatures:• Seamless alignment for that oh-so-clean look.• Lack Drawers also include...

it's designed to be printed in TPU.You can use this on frames such as the [Pickle], [Kabab's TP3], [RacerX TWIG] and virtually any setup that relies on an AIO flight controller.Want to buy the PicklePod2 ?If you cannot print it, this pod is being...

;-) All gcode files are made for Prusament PLA but any other PLA will work fine. Have fun printing this one and I am excited to hear your thoughts!  Some info about Awakenings. (source: Wikipedia)Awakenings is the collective name of techno parties...

Features: Guardian Angel delivers military and civilian leaders eight foundational capabilities across the Personnel Recovery continuum: 1) preparation of potential isolated personnel; 2) completion of Personnel Recovery mission planning; 3)...

... you liked this, please leave a like. I am offering this free for everyone and also you are allowed to make any customization. I do not earn nothing with this but I like to help. ...So help me with a like, so this model reaches to more people!

This resulted in two separate roofs in the source plans; you will need supports enabled to print the overhangs on the roof successfully.\nI printed with PLA without any issues or layer shifting.\nPost-Printing Assembly\nThe kiosk is held together...

The knurling also comes out really well on layer heights less than .20 mm, but should turn out with any layer height. ### Entire Assembly at Once, Single Setting Build time: 7 hours 28 minutes Plastic weight: 66 g Layer Height: .15 External Fill...

I used a cleave at the back to mount the board in place. Mounting pucks:There is enough friction between the male/female part of the puck where you do not need any adhesive to keep them together. The can be separated to allow for the swapping of...

With its intricate dragon scale design and rich, dark wood finish, it's the perfect addition to any room - whether you're a fan of the show or just someone who appreciates the beauty and craftsmanship that goes into creating such an iconic piece. In...

In Cura this can be found under: Extensions > Post Processing > Modify G-Code > Add a script Finishing with glitter You will need: Water-based découpage glue - clear gloss works best A fine brush - one you are happy to use to apply the glue Glitter -...

It has been on my car in the Florida June sun for about a month without any problems. If you use a different color PLA or have a car with a darker color than silver then you will likely have issues with melting/warping on the car without annealing...

You'd be pushing the filament from several tens of mm back from the tip, and with the natural curve to any filament coming off a spool, it is very easy to snag even a tiny lip and jam up. But, mainly due to peer pressure from my buddy Olof Ogland, I...

Movement in the Z direction The Dual Axis V-Pivot constrains the degrees of freedom of motion to any two of the follow degrees of freedom of motion 1. Rotation about the X axis (pitch) 2. Rotation about the Y axis (roll) 3. Rotation around the Z...

 Bottoms fit both top sizes, only the side mounting rails are affected by different tops.No Hardware: This design does not use any hardware and all parts are “Snap-Fit.”  There are small tabs that flex a tiny bit to allow a lip to snap into...