FlashForge Creator Pro bed leveling jig 3d models

... 60mm in length and are spaced 81mm center to center. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20mm or less Infill: 15% - 100% Notes: The model was printed upside-down with adequate support throughout.

This holder was created for securing spray bottles and parts at the corners of a flashforge creator pro printer. As seen here, you can insert whatever fits inside it. Instructions A corner solution was sought out to hold multiple...

The shape is designed for the flavors of the FlashForge Creator Pro (2016 edition) that have long-shaped feet, but they will fit any machine with feet shaped like a rounded rectangle about 48×17mm in size, at least 2 mm high. Of course you can scale...

To attach the new latch, follow these easy steps: Remove the central screw (2.5mm hex) from the front frame of my Flashforge Creator Pro Printer. Next, insert the screw into the holder and screw it down tightly until it is fully secured. Carefully...

Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Infill: 30% Notes: The filament tubes fit very snugly. To get one tube to go in, I had to remove a burr. If it's too snug for your tube, try rolling up some...

I found a bit annoying that on the the Flashforge Creator Pro you can have the problem of filament spools falling from the shallow holders of the printer. This happens with most brands of filament. I have some GeeeTech, 3D Kaige and other brands,...

... Update (Feb 2016): Humanisticnick reported that this dome works perfectly with the FlashForge Creator Wooden: "I simply needed to trim down my filament guide tubes." This product describes an improved dome for the Flashforge Creator Pro 3D printer.

This improved dome has been designed specifically for FlashForge Creator Pro and provides several upgrades compared to the stock version: Better filament path: The new design moves freely. Improved heat enclosure: Since the opening is located at...

This thing describes an improved dome for the Flashforge Creator Pro 3D printer. This dome has a few advantages over the stock one. Better filament guide path that moves freely. Better heat enclosure, the opening is at the bottom so heat is...

This configuration allows flat printing without glues or supports required.\nSlicing Parameters\nPrinter Specifications\nDevice: FF Creator Pro\nFeatures: No rafts, no supports used in this print.\nLayer thickness: .15mm high-definition resolution...

This is a drop-in replacement fan duct that fits the FlashForge Creator Pro and similar models that have the ‘turbo fan’ at the left of the nozzles. It has been confirmed to fit the 2015 FFCP (upwards opening door), the 2016 (sideways door), and the...

This is a top handle for the Improved Dome for Flashforge Creator Pro thing http://www.thingiverse.com/thing:1194887, making it easy to remove and place the dome with one hand. The creator customized the parametric handle generator...

This is a top handle designed for the Improved Dome on the Flashforge Creator Pro thing, accessible at http://www.thingiverse.com/thing:1194887. It makes removal and placement of the dome straightforward using one hand. The creator of this thing...

Print Settings Printer: FlashForge Creator pro Rafts: No Supports: No Resolution: 2mm Infill: 100% Notes: Black ABS from Makerbot, 2mm layers, 4000mm/s on FF Creator Pro (1st layer 50% speed) with all metal hotend (0.4mm). Using 3 layers of 2...

Universeller Filament Rollenhalter. ... Ich habe ihn aus ABS mit 35% Infill gedruckt. Hält super und nun passen alle Filamentrollen ohne Probleme hinten an den Creator Pro

ULTIMATE FILAMENT GUIDE For Flashforge Creator Pro (and similar compatible machines) This guide includes a comprehensive dust filter system and allows your filament to travel from the spool to the extruder with minimal exposure to air! Used in...

Print Settings: Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 20% Notes: The Hanger part needs supports, and depending on your printer's bridging capabilities, the "PEX END" part might need them too. If...

This is a 3D printed upgrade for the FlashForge Creator Pro's spool holder, designed to hold various spools on bearings for easy rolling. The purpose of this upgrade is to provide a convenient way to manage multiple spools. The spool holders are...

Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Notes: Printing this in a flexible filament will make installation easier, and reduce or eliminate rattling sounds. If you print it in an elastic filament, it may...

However, my Creator Pro had a limitation - its extruder assembly lacked screws long enough to reach the aluminum block. To overcome this issue, I shortened the distance between the ledges and the bottom of the print bed so that even the longest...

... creator printers out just to change the filament. ... So I designed this filament holder that fits on both of our creator Pro and Pro 2 printers. Depending on your print you may have to glue the 2 parts of the main body together. ... Printed in PLA+

Instructions This is designed for my printer (FlashForge Creator Pro), but it should mount on any similar extruders. I've heard that some printers have aluminum mounting blocks mounted in different positions, so you might need longer or shorter...

Looking for a simple, straightforward and highly effective FlashForge Pro Creator filament guide holder? You've got it right here. This uncomplicated replacement is robust, lets you position it however you like and won't get in the way when you need...

This is a small upgrade for the recent edition of the FlashForge Creator Pro. It is a support that helps to keep the umbilical cord between printer and nozzles upright. Without this, the cord tends to sag to the left on my printer, increasing the...

Looking for a simple yet robust FlashForge Pro Creator filament guide holder? You've come to the right place! This straightforward replacement is designed to be strong, versatile, and won't obstruct your work when you need to remove the back panel of...

... is intended to be printed without support structures (those pesky annoyances), which can often get in the way of a smooth print job. Print Settings: Printer: FlashForge Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 25%

These spool holders are designed specifically for the FlashForge Creator Pro 3D printer. I experienced problems with other spool holder designs, as the filament would occasionally fall off the spool due to the edge of the roll being offset from the...

Looking for a straightforward, robust and efficient FlashForge Pro Creator filament guide holder? You've found it! This is a no-nonsense replacement that's strong, lets you position it however you want and doesn't get in the way when you're working...

To keep your workspace safe from fumes, simply slide this convenient vent over the finger hole on your Flashforge Creator pro. Installing it is a breeze - don't let these instructions fool you into thinking otherwise. This attachment was specifically...

### This Is Not a Standalone Print As designed, it is intended for users to overlay a picture or some text onto the model to make their FlashForge Creator Pro truly unique. ### How To Install After printing has been completed (ensuring the model...