Humidity and Temperature Sensor Housing 3d models

I built a custom version of the Sonoff Basic Decora Cover with capacitive touch, adding a PIR sensor and a temperature/humidity sensor. I linked it to home-assistant using ESPhome. The PIR sensor used is an AM312 from Amazon, available at...

Part of that involved a DHT-22 temperature and humidity sensor to monitor the internal conditions. This adapter enables you to mount the sensor in the place where the wet bulb thermometer adapter normally mounts. It has the same fixing holes as the...

Housing for using a temperature sensor DHT22, AM2302 or DHT11 sensor outdoors to protect it from sun and weather. The cover has stacked "roofs" to allow air to pass through but keep water and sunlight out. The sensor holder consists of 3 parts. The...

This device was engineered to accurately gauge both humidity levels and water height, then swiftly transmit its findings directly to the user's smartphone.

delay(10000); // read humidity float humi = dht.readHumidity(); // read temperature as Celsius float tempC = dht.readTemperature(); // read temperature as Fahrenheit float tempF = dht.readTemperature(true); // check if any reads failed if...

Overview video for this sensor: https://youtu.be/VefbT6RuT-4 Build video (part 1 - hardware): https://youtu.be/fA91LcJRbhI Build video (part 2 - software): https://youtu.be/uDsnqi1Vl4U Build video (part 3 - openHAB): https://youtu.be/yHt19wZBnDo SEE...

This is a versatile enclosure designed specifically for use with a D1 Mini microcontroller and the SHT30 sensor module, allowing users to easily capture temperature and humidity readings.

I have the AcuRite 01083 temperature/humidity sensor (https://www.amazon.com/dp/B01HDW58GS/ref=cm_sw_em_r_mt_dp_U_.Z7cEb3HV3BKW) for my drybox, but I wasn't satisfied with how it looked in there. It would tilt and jostle around when the box was...

This is repaired holder model of Stevenson screen for Xiaomi Aqara Temperature, Humidity and Pressure zigbee sensor (https://www.thingiverse.com/thing:4620242).

I designed a mount to use the small rectangular temperature/humidity sensors ( https://amzn.to/372N2eJ ). It uses the upper filament port to mount. That way no modifications are required to the dryer. I found it works better if you store...

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm Category: Hobby

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm

I needed a stronger mount for the Outdoor+station+for+Aqara+Temperature+and+Humidity+Sensor\files https://www.thingiverse.com/thing:4223141 wall thickness is 3mm and all the polt and screws holes are 4.5mm

The Xiaomi sensors are a fantastic and affordable way to do this, but attaching them directly to the pipe wasn't a viable solution. So I came up with this alternative. It can be securely fastened onto a 15mm pipe. Additionally, I'm currently...

... up damaging the paint and having to use a new sticker. Instead, just print out this mount and slide the sensor into it. ...The sensor already has its own sticker attached, so you can easily stick it to the wall using the second sticker provided.

The Holder can be used with the adhesive sticker provided in the box or your own and it allows the sensor to be easily removed for battery replacement. I have added a hole that you can use to hang it on a nail. There is also a hole for a magnet...

Mount for the Aqara sensor. One for use with a nail the other can use screws. ...

CJMCU-680, BME680 Ambient Temperature, Relative Humidity, Barometric Pressure, and Gas VOC SensorContains 4 sensors in 1 module.Temperature and humidity can be used for weather monitoring, process control, etc.Barometric pressure can be used for...

I admired twamueller's creation (2617289), but it hindered rotation for battery change and required removal of the sticky tape to unscrew it. This design allows both rotation and unscrewing without having to reapply any adhesive. ... There is a...

The Xiaomi temperature and humidity sensor is securely held in place by hand. To mount it, simply drive a common drywall screw into the surrounding wall or fasten it down with a ziptie. A small flat bit at the top of the mounting hole makes zip-tie...

It is convenient that it allows you to remove the sensor without dismantling the entire case, on the latches, which is convenient when the device is hanging outside the window at a height. Special thanks for the help in creating and developing -...

CJMCU-680, BME680 Ambient Temperature, Relative Humidity, Barometric Pressure, and Gas VOC SensorContains 4 sensors in 1 module.Temperature and humidity can be used for weather monitoring, process control, etc.Barometric pressure can be used for...

A taller case to fit the DHT22 that has a circuit-board attached to it.Can be added to an IKEA air sensor: https://www.thingiverse.com/thing:6403319

I was in need of a wall-mountable box to house an Arduino Uno, paired with an IR LED and an external DHT11 humidity and temperature sensor. I also required sufficient space for the RFM69HW radio hardware, complete with its internal antenna. The...

Measure your soil moisture with some capacitiv sensor, this housing will hold the sensor a dallas temperature sensor and a Wemos D1 Mini. ... Glue all holes tightly, you'll need 2 M3x12mm or M3x20mm screws.

The changes made to the original file were: Reshape the object to avoid placing the supports and I made sure that the center of gravity falls in the center of the base. If you found this useful, please donate what you think it is worth to my...

The modifications applied to the original file were:\r\nI adjusted the object's shape to prevent placing supports and ensured that its center of gravity aligns with the base's center.\r\n\r\nIf this information was helpful, please consider making a...

Stevenson screen for Xiaomi Aqara Temperature, Humidity and Pressure zigbee sensor (WSDCGQ11LM). Also fits with Sonoff SNZB-02 (bracket attached). This remix is based on 2 projects as below: https://www.thingiverse.com/thing:2970799...

The Xiaomi temperature and humidity sensor is held firmly in place by a square enclosure designed by me. I believe it's actually the Aqara version, which mounts securely with either a drywall screw or a zip-tie. The screw hole features a flat surface...

Holds the square Xiaomi temperature and humidity sensor. (I think this is the Aqara version?) It mounts with a common drywall screw, or with a zip-tie. (There's a flat bit at the top of the screw hole to make zip-tie mounting a little easier). I...