IQaudIO Pi DAC Case for A 3d models

The IQaudIO Pi-DAC+ boasts an integrated headphone amplifier, as well as RCA line-outs, making it a versatile choice for any audiophile. The case can be positioned in multiple orientations to suit your needs. While the optional bumpers are not...

The Pi 3 A+ coupled with the IQaudIO Pi-DAC Pro hat makes for a compact Roon bridge. Remix Details: * The RCA holes have been relocated. * An M3 screw hole has been added. ...* The Pi's 3.5mm jack has been disabled, as it is in RoPieee, and the hat...

Pi 3 A+ and am iqaudio pi-dac pro hat make a nice small Roon bridge Remix details: Relocated RCA holes M3 screw hole Covered the pi 3.5mm jack as it's disabled in RoPieee and the hat has one

I made this simple case for a Raspberry Pi 4 with the IQaudio DAC+. I run Volumio on that thing and it works great. I like to have the Pi cool, so I add a 30x30mm Fan from an RC Car ESC, which I power with the 3.3V from the Raspberry Pi. If you like...

I made this simple case for a Raspberry Pi 4 with the IQaudio DAC+. I run Volumio on that thing and it works great. I like to have the Pi cool, so I add a 30x30mm Fan from an RC Car ESC, which I power with the 3.3V from the Raspberry Pi. If you like...

I made this simple case for a Raspberry Pi 4 with the IQaudio DAC+. I run Volumio on that thing and it works great. I like to have the Pi cool, so I add a 30x30mm Fan from an RC Car ESC, which I power with the 3.3V from the Raspberry Pi. If you like...

For this version, you can use the same screws included with IQAudio DAC+ kit. ...Original version needed longer screws to attach raspberry pi board.

For this version, you can use the same screws included with IQAudio DAC+ kit. ...Original version needed longer screws to attach raspberry pi board.

IQAudio DAC Pro and Raspberry PI 4 case modification.Remixed from...HifiBerry Case by Stamoshttps://www.thingiverse.com/thing:4208854IQaudio DAC Pro Case by @dirkmeineke_210551https://www.printables.com/model/561600-iqaudio-dac-pro-caseHonourable...

This is a quick-assemble case designed specifically for a raspberry pi Zero W and connected IQAudio Pi Zero DAC plus Headphone Amp. The top and bottom pieces take approximately 1.5 hours to print. Assembly: 1) Attach one M2.5/9mm standoff to the...

I built a 3D printed enclosure for my Raspberry Pi using an IQAudio PI-DAC+ running Volumio, hoping it would be helpful to others too. The Pi stays securely in place with standoff screws at the bottom and the lid clicks on easily. ... The decorative...

I got a IQaudio DAC Pro hooked up to a Pi Zero W. I was thinking about where to use it, but most usecase require a mobile setting which requires battery. This case fits 2 18650 Li-Po battery, 1 USB charging IC (TP4056), Pi Zero W and DAC Pro.

<p>It is just two separate parts, connected by one screw. ...The LCD, encoder, Raspberry pi and DAC are also bolted together.(Access to the screws could be optimized further). ...But the final print accomplished what I needed from it.</p>

This is a remix version of the Honeycomb Case sled fitted with holes for the Hifiberry DAC+ Its quite a loose fit, so maybe a bit of scaling will help. ... This is my first time using CAD, so my apologies if it isn't as refined as it coud be.

Modifications to the original Thing: - moved and enlarged the hole for the 3.5mm jack on the hat - added four screw holes to the base so that the box can be attached to a surface - in order to be able to use the M2.5x8mm screws, I have cut out a...

This is a case for an old Raspberry PI 1B with an audio DAC. I created this case because all Raspberry PI 1 cases I found did not provide a clean design and left the SDCard accessible directly from outside. ...I'd prefer to have it integrated into the...

Just a top case to enclose a rpi with hifiberry DAC+. No screw needed. Slim fit. For base of the enclosure check remixed thing. ...

A remix of the HifiBerry Case by Stamos (https://www.thingiverse.com/thing:4208854) to fit the Allo Boss I2S DAC (https://allo.com/sparky/boss-dac.html) for Raspberry Pi 4.

This is a case for Raspberry Pi 3 B+ and Allo Piano 2.2 DAC. I use this for playing music in my network. I didn't find a proper case for this combination, so I made a model which fits my needs. I did not print this case by myself, I use a 3d...

This is a project for the Raspberry Pi 3 B+ and Allo Piano 2.2 DAC combo. It's used to stream music throughout my network. After searching, I couldn't find an ideal case that matched this setup, so I designed one to fit my requirements. The actual...

I ran into trouble designing a closed case for Raspberry Pi, given that there are plugs on three sides. The project gets even trickier when you need to add extension boards.\r\n\r\nSo I opted for simplicity. It's an open design made from just 2...

I use this for playing music in my network. I didn't find a proper case for this combination, so I made a model which fits my needs. I did not print this case by myself, I use a 3d print-service... The repository can be found on my website. Have fun!...

This is a straightforward project intended to safeguard a Pi Zero WH equipped with a HiFiBerry DAC+ Zero connected to its header. The enclosure consists of three components - a Base, a Spacer, and a Top - each serving a specific purpose. These parts...

... the HifiBerry Dac+ soundcard at the top. ...The print boasts a snug fit between the card and Raspberry Pi, eliminating the need for spacers, while the headphone jack slips effortlessly into its corresponding hole, ensuring a stable connection.

Furthermore, I've designed a lid with supports for a 45-degree housing. However, it's essential to note that this lid requires a lip to securely hold the case in place. ...Without this feature, the case may slide down if not placed on an absolutely...

I'm excited to share this project with Raspberry Pi (https://amzn.to/2ReJHj4) and DAC Hat (https://amzn.to/2KfJj3b). The cap is secured in place by two M3 screws. ...You can attach the Pi using M2 screws without any modifications, but if you prefer to...

A printable case for Raspberry Pi + DAC Hallo Boss

This is a two-part case for a Raspberry Pi Model 3A+ with a Raspberry Pi (IQaudio) DAC+ designed to assemble with brass standoffs and machine screws, although the case snaps right together and will probably hold the electronics well enough without...

Here is a rewritten version of the original text: A custom-made 3D printed enclosure fits snugly over the IQAudio Pi DAC Zero and Raspberry Pi, a perfect marriage of innovation and precision engineering.

This is an inno-maker usb-dac case. ...Optimized for raspberry pi zero w. ... You need M3x8 (or M3x12) hex head screw x 4 M3 din562 square nut x4 Details of usb-dac https://www.inno-maker.com/product/hifi-dac-hat/ Enjoy your Volumio life.