Library Box Case for TP Link MR3040 3d models

... this to mount a Kasa Cam KC110 that its mount had the tabs broken off. ...This works like a charm. I would recommend anyone that uses this make the base slightly thicker and add a dent for the screw heads. ...Other then that this design works flawless.

I designed this wall mount for my TAPO c110 camera so I don't have to drill holes in the wall and instead,I used double sided mounting tape, and I use this camera in multiple areas, so I can easily remove and install it in other area.

Added third holder at the bottom, so you can hang it upside down if needed.Lid fits better, it's tighter, by higher and a bit wider walls.But still I used glue to connect it.I added as well 2 blocks to keep the distance from the wall and keep the...

If you're going to print this, make sure you have tuned your printer very well for dimensional accuracy, as there is very little room for error. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2mm...

The lock is intended for use with a 37mm diameter umbrella pole, although it may also fit poles measuring between 36-38mm in diameter, although this has not been thoroughly tested. ...If you found this information helpful, please consider making a...

... needs. ...The two studs now securely hold the router in place, sliding neatly into the small gaps between them. I printed with PETG because that was all I had available, and opted for 100% infill since such a minimal amount of material was used anyway.

... you want to mount the plate and attach the switch. You will most likely have to sand off a bit of the sides for it to fit looser or leave it as it prints to have a snugger fit. ... I printed using normal supports touching the build plate only.

... overhang for the 2 studs but still snaps in place nicely. UPDATE: created V2 for those that want to flip the switch over to more easily remove the ethernet plugs, as before leave on your rubber feet that came with the switch. ... Prints in 2 parts

But for our purposes, this wall mounting was no option and the device had to be placed on a desk or other furniture. It is printed in two parts which have to be assembled using two M3 screws (left side) and two M3 inserts (right side). Two extra...

This is a remix of this mounting plate by asp55 on Thingiverse.This one has the inserts a bit closer than the original to fit newer TL-SG105 switches.Just use double sided tape or whatever you want to mount the plate and attach the switch.You will...

I made the prongs and cross pieces both thicker, and added an extra prong for good measure. I also made the top of the prongs a little longer to make sure it held the deco in firmly and wouldn't slip out if it was bumped. Note that it's a pretty...

You might just need to sand them a little bit depending on how your printer handled the last few layers If you are looking to use it for something else, the holes should be spaced by 13cm, and about 5mm deep. Print Settings Printer Brand: Prusa...

Thanks to the make by DasFasty for testing the M3 version! https://www.thingiverse.com/thing:3758303 This is a 1U space for two TP-Link TL-SG108 or Netgear GS308 8 port GigE switches. It also can take the TP-Link managed 8 port switch as well, which...

Academic project for hard surface modeling and texturing. The base model was provided by the instructor in a low-poly form. ...Baking and textures were created by myself.

Standing upright next to the Tp-Link TL-SG1024DE \r\n\r\nManufactured from PET-G Taulman plastic\r\n layers at 0.4mm thickness \r\nfilled with material up to 30% capacity \r\nwith a finish of 1.2mm smoothness

GoPro mount for TP-Link Tapo C100 IP camera

Support legs are available for TP Link AC5400X and TP Link AX11000 models, featuring a 140mm cooler reminiscent of the Noctua design.

Simple mounts for TP-link UH720 usb hub.You need 2 for mounting

Simple Wallmount for the TP-Link TL-MR3020 N300 WLAN Nano from 3mm plywood.

TP-LINK rack mount kit for TL-ER7206 router 1U rack 19P

Tp-link Omada OC200 Rack mount kit for 10 inch rack. ... 100% infill With supports

Wall Mount for mobile WiFi travel router TP-Link TL-WR902ACMount with double-sided sticky tape.

TP-LINK DECO M4R BOARD MOUNT

... 1. CE3PRO_ASIAir Pro + TP Link V3 Upgrade.stl contains: * CE3PRO_ASIAir Pro + TP Link Top V3.stl * CE3PRO_ASIAir Pro + TP Link DC Adapter Top V3.stl * CE3PRO_ASIAir Pro + TP Link DC Adapter V3.stl 2. CE3PRO_ASIAir Pro + TP Link Middle V2.stl 3.

Small modifications to my Snapmaker 2.0 A350T check the printing status via app and also create timelapse videos

I tried to print and I found it hard to remove all the support materials. ...So I split it into two parts, top and bottom.

I've repurposed this section to attach the switch to my Ikea Lack enclosure utilizing screws. ...The switch resides discreetly behind the Ikea Lack table.

This is the combination of a Manfrotto 200PL quick-release plate with a Tapo C200 mount.

This creation was crafted using Tinkercad's innovative design tools. ...Make your edits directly online at https://www.tinkercad.com/things/czjMuLBwVxY.