Light Switch Dimmer Knob (for broken switch spline) 3d models

As they approach the dimly lit room, Batman gives Krypto a reassuring pat on the back, saying "It's time, boy, let's get this done." With a flick of his cape, Batman strides towards the light switch and flips it with ease, casting a warm glow over...

It should work with most any toggle style light switch. I have printed and can verify the dual switch works. I have not printed the single triple or quad setup. That being said they should all work as intended. On some switches, the rectangular hole...

It should work with most any toggle style light switch. I have printed and can verify the dual switch works. I have not printed the single triple or quad setup. That being said they should all work as intended. On some switches, the rectangular hole...

I employed various components to construct a Powder-Coating Oven, including a Green LED switch with On/Off functionality, a RED light accompanied by a sound alarm, and additional parts. I uploaded these designs on GrabCAD for future reference in...

This is a custom extender arm for a standard light switch that can be adjusted to different lengths. I designed it after finding similar products online but couldn't locate them again, so I took matters into my own hands and created one myself. To...

The original design didn't work for my specific application with an IR light fixture switch. The panel on the left is a custom STL model I've designed and included, while the model on the right is from Thingiverse's number 2079642. Left model...

LoboCNC, your design for the Frankenstein Light Switch really shines. The only catch was that the two up modern configuration took up too much space in my Printrbot Simple's Y 100m limit. I'm sure many users are stuck with this same limitation. One...

I have a powered height adjusting desk (uplift) and it is against a wall with 2 (separated) light switches. Without protectors (or with the original design) when I lifted or lowered the desk it would flip on or off the switches. The protective fins...

Replacement knob for ASR-33 mode switch selector.

Fits standard light switches.The design hides layer lines fairly well. The body requires support, the pieces do not. I would print 1 full set in each of 8 colors, then mix and match and glue together (which gave me a lot of covers to give away). I...

Ever had a rocker switch for a ceiling fan that CANNOT be turned of or the house becomes a desert? ... I hope this solves the problem.

Ever had a rocker switch for a ceiling fan that CANNOT be turned of or the house becomes a desert? ... I hope this solves the problem.

Temporarily or permanently locks switch in place for safety and peace of mind during crowded events where guests frequently flip wrong switch. Useful if a circuit needs to stay consistently on or off for a specified time period. This part prints...

Fits in place of your standard wall switch plate and has a large toggle that slides over the standard toggle. Satisfying, easy to use and fun. This can also be useful for people with limited mobility or children's rooms. Easy to assemble: First...

This design also allowed me to add a cavity in the back plate that clears the switch's ears, making it easier to install.\nThe mounting screws hold both the front and back plates in place securely, which is exactly what I was looking for. Now all I...

I found this one on the site: http://www.thingiverse.com/thing:6688 I made it and it worked, but it's too thin on one side and I wanted to print it on glow-in-the-dark PLA so I could see switches when the lights were off & it didn't print well on...

I found this one on the site: http://www.thingiverse.com/thing:6688 I made it and it worked, but it's too thin on one side and I wanted to print it on glow-in-the-dark PLA so I could see switches when lights were off & it didn't print well on PLA. I...

The companion component, "Badass Arduino Box" (http://www.thingiverse.com/thing:923242), has been meticulously crafted to complement the Smart Switch Module's cutting-edge functionality and sleek aesthetic, resulting in an unparalleled technological...

I have a few switches in my house that for various reasons I don't want people (including myself) to turn them off inadvertently. This simple clip screws onto the switch plate and can prevent the switch from being turned off or on (depending on...

English This basic light switch cover is built from two key components. The outer part conceals the electrical wires of the switch, while the inner part surrounds the switch button. To access more information and additional files, visit our website!

Breaking old habits was a challenge we faced after installing smart lights - our fingers instinctively reached for those familiar light switches instead. Crafted with practicality in mind, this innovative cover is designed to seamlessly attach to...

So I created this cover to go over the existing rocker switches, and have a place for some ZigBee switches. This is for a standard US single gang (1 switch) box, as well as a shallow inset to fit in the ZigBee switch. There's a small bit of room,...

This is a switch/outlet plate that uses magnets to stay on the wall. ...This was for internet connected switches that I installed that did not have screw holes for the plate. ... I can make a custom one by request for a (very) small fee.

... did a while back. It adds a traditional switch, a hand held design, and a second handle to the designs. I did this for accessibility or for people otherwise unable to reach the switch. ... A little sanding is likely required for the tee slot joints.

This is a mash up of the mermaid found here: https://www.thingiverse.com/thing:2950745 and the light switch panel found here: https://www.thingiverse.com/thing:4502452 I did use a raft and tree supports. Printed with an Ender 3 pro. ... If you can and...

This is a mash up of the mermaid found here: https://www.thingiverse.com/thing:2950745 and the light switch panel found here: https://www.thingiverse.com/thing:4502452 I did use a raft and tree supports. Printed with an Ender 3 pro. ... If you can and...

This is a mash up of the mermaid found here: https://www.thingiverse.com/thing:2950745 and the light switch panel found here: https://www.thingiverse.com/thing:4502452 I did use a raft and tree supports. Printed with an Ender 3 pro. ... If you can and...

After looking at the other light switch guards, I needed one that is more secure. This cover I've designed is not only a guard, but also kind of a lock. You can still activate the switch via the 4mm hole at the top and bottom with a toothpick or...

A case designed to house an exterior-mounted light switch, typically made of durable plastic and designed to withstand various weather conditions. It usually features a waterproof seal to protect against rain or snow, ensuring the switch remains...

I have many light switches around the house, many of them controls fans and lamps i don't want My kids to turn on/off so i had 3d printed more complicated ones before ,this time i want to create the simplest i can design and this is my first attempt...