Precision 2 and 3 ski edge file guide 3d models

I made an improvement on BlartVersenwald's Screw Stabilizer project and merged it with Filament Guide's D3D_Designs project. Now it's not as long as before and it doesn't hit the bottom filament guide if the print is high. There is also an...

This is the sensor I used: https://www.amazon.com/gp/product/B081W4KMHC/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 This works well with OctoPrint and the enclosure plugin. ... You can add a rubber band or small screw to the end of the sensor arm...

Since mine had been sticking on the bearing, adjustments made it to pull consistently clear of that edge

I search a lot for a better stabilizer and guide fusion but now i design a fusion of two really good thing. Thanks for the models to Breinstorm and ElevationsTech!!! If you like my thing or just want to support, buy me a cup of coffee! ...:)...

I search a lot for a better stabilizer and guide fusion but now i design a fusion of two really good thing. Thanks for the models to Breinstorm and ElevationsTech!!! If you like my thing or just want to support, buy me a cup of coffee! ...:) ...

I appreciated the original design's use of PTFE tube as a guide and upgraded mine accordingly. Cutting a section from the stock tube greatly improved the transition into the inlet. I made several modifications to enhance functionality: * ...

Decided it would look nice if it had a little loop in it...you can read up on the Golden Spiral here : https://en.wikipedia.org/wiki/Golden_spiral Mount the bracket between the spool holder and the aluminium extrusion, bolt holes are M5. ...Openscad...

just made a easy mount for a 5 galon bucket all you have to do is cut the hole in the center of the regular lid or i used a 6" net pot lid for a 5 gallon bucket and it worked well to guide the tubing

I merged the E bracket mount (https://www.thingiverse.com/thing:3190998) and this filament guide (https://www.thingiverse.com/thing:2920344) into a single unit. If you want to install them stacked on top of each other, the factory screw is too short....

... a wire guide to the spool holder, which has greatly improved the organization of my project. ...The added feature has eliminated the pesky issue of wires getting tangled, caught, or wrapped around other components during assembly and disassembly.

The roll will guide the filament into the runout sensor and from there into the extruder. I designed this based on the remixes mentioned. You can take out the runout sensor from the original CR10s and place it into this design. ! Print the...

Needed a filament guide to keep the filament feeding from my spool from getting into the way of my lead screw. Decided it would look nice if it had a little loop in it...you can read up on the Golden Spiral here :...

In addition, a dust filter from https://www.thingiverse.com/thing:2349995 and a secure fastening system for the hotend cables are integrated. ... The design also features a notch that simplifies positioning on the extruder motor, so it should be printed...

Filament bearing guide and runout sensor. Broadly based on https://www.thingiverse.com/thing:4079159 but designed from scratch, so more "inspired by", than remixed :-) Update 06/04/2021 - Completely re-designed from scratch in Fusion 360. Switch...

* If you want to print with cap, use the files Ender_3_V2_-_Runout_Sensor_Base.stl and Ender_3_V2_-_Runout_Sensor_Cap.stl, if not, use only the file Ender_3_V2_-_Runout_Sensor.stl. * If you use stock firmware, probable you will need to update it...

The basic geometry is unchanged: It still consists of a bracket, a switch/bearing plate, and a cover - I've done away with the Z-rod guide as, in practice, it's redundant; the entire assembly already keeps the filament away from the Z-rod. It also...

This is for use with aftermarket extruder, Extended guide roller mount to accommodate larger roller for an easier filament turn.

This lets me use an arbitrarily long scrap of old tubing to guide the filament from the spool into the extruder assembly, with nice gentle bends and curves regardless of print height or spool placement. In fact, the spool no longer needs to be on top...

... using a 1.6mm build wall to accommodate the tap. I purchased some affordable metric tap drills from Amazon. It cost $12 USD for a set with M3, M4, M5, M6, M7 and M8. I designed this in Solidworks 2016 and have included the source file. ...Enjoy!

This guide works seamlessly with both the standard extruder frame and the slightly taller double-gear extruder frame, which has a raised filament hole compared to the standard one. This design centers around this switch:...

... Thanks to Michael for sharing! This filament guide and run-out sensor bracket measures 46.5x28.7x27.0mm, is made from PLA material with a diameter of 1.77m, weighs 5g, and takes 43 minutes to print at a layer height of 0.12.

Visit my Patreonhttps://www.patreon.com/Belksasar3DPrint High poly model of a Succubu varianst 2 and 3 done in Zbrush, projected to be in 30mm and 55mm, can be print bigger or smaller. Ideal for resin printers, supports included. The files Contain...

... hole is smaller and it will be self tapped by that screw. Rotate roller model to be flat on the table. (strange Fusion360 Axes) You don't need bearings and other stuff, the roller is rotating freely after few screw pushes inside a hole. ...

It's a bit larger than some others, as I wanted it to combine both functions AND eliminate the need for any other filament guides customarily added to the E3. There are many solutions to a clear filament path, but I keep my reel holder as far to the...

... 608). Install Guide: - Insert bearing into printed part - Remove top two screws above z-rod using 4mm allen wrench - Mount printed part - Fasten printed part with screws using same allen wrench For more secure threads, remove washers on screws.

the original was not firmly enough in the profile of the ender 3 pro, i fixed that and made it a little less angular.

Raspberry PI 3 Plus Models One B and Two with SD Card Added and Real Ethernet and Real USB.

I designed a 7mm version using Fusion 360 for the first time, and I'm excited about how useful it turned out. ...The dimensions are identical, with one exception - the longest component is now 3mm thick.

Only modification made was to accommodate 3/4 inch MDF, which actually measures 19mm thick. ...Refer to machadolab's original design for further information.

Eléments basés (mais redessinés) depuis les sources suivantes: https://www.thingiverse.com/thing:4185537 https://www.thingiverse.com/thing:4683505 https://www.thingiverse.com/thing:4695818 https://www.thingiverse.com/thing:4720152 This associated...