fd lens cap 3d models
96263 3d models found related to fd lens cap.thingiverse
Just a simple lens cap for Canon FD. ...It's a tight, nice fit, but that depends on your printer and how it handles overhangs.
thingiverse
There are other Canon FD lens caps around, but for whatever reason they didn't print right, so I just designed my own. Fits well on both DF and FDn lenses, however, depending on how well your printer is calibrated, you might have to fine tune the...
thingiverse
Lens caps tend to disappear again and again in mysterious ways. Especially the ones for the back. Since there are only expensive used ones left for the FD system (or cheap ones from China with correspondingly long delivery times) - I quickly designed...
thingiverse
I have designed this cap based on my measurments. I am currently printing a proto. I will keep you informed as soon as the final design works very well. FYI, mine is printed in PLA (wall of 2 mm, top/bottom of 1,5 mm, and infill of 50%). Tips...
thingiverse
I flipped the design by @adrianS2 and cleaned up the angle so that on my Ender 3 Pro it prints without supports.
thingiverse
This is a remix of nick_nugget's Canon FD rear lens cap (updated). I'm mostly sharing this so others can use the same idea for their lenses, but since the 50 f1.8 is so common, I figured someone would probably need this one specifically. I used...
thingiverse
For EF, PL, MFT, E, M mount rear caps, please refer to the link below https://youtu.be/wjHL6QEp2jM In most cases, there is not much difference in the function of the lens rear cap, so this lens rear cap also makes no difference except for...
thingiverse
Simple Canon FD mount cap designed for FD (to MFT) adapters Printed face down, no supports, PLA FD logo perpendicular to mounting dot
thingiverse
Just a simple body cap for a Canon FD mount. ... It's a lose fit, but it should be tight enough to not come off on its own.
thingiverse
You can gue inside the cap the lens mount adapter so that the lens stay tight and safe inside the box. I added some tape foam inside and at the bottom of the container. I also used red nail paint to fill the Canon text, which is 0.4mm extruded into...
thingiverse
... can crack. There should be a small gap when tight between upper and lower. This is normal. Hardware: 1X Canon FD 70 - 210 lens 2X 5/16" x 1 1/4" 2X Hex Nuts 5/16" 1X Compatible Manfrotto 200 PL Tripod Please let me know if you find this useful!
thingiverse
Lens hood for 55mm Canon FD. Should fit 55/1.2 and likely others with 58 mm filter ring. ...Supports recommended for attachment ring.
pinshape
... working lens adapter for Canon FD lenses. ...Fits GuerillaBeam projectors (with the ability to focus to infinity). Pros: Cons Because the FD mount mechanism demand that the part is very thin, it is not as robust as the other GuerillaBeam lens adapters
thingiverse
Lens hood for 28mm Canon FD. Fits 28/2.8 and likely others with 52 mm filter ring. Modeled after Canon BW-52B. Snug fit and can be attached backwards for storage. ...Supports recommended for attachment ring.
thingiverse
Lens hood for 50mm Canon FD. Fits 50/1.8, 50/1.4 and likely others with 52 mm filter ring. Modeled after Canon BS-52. Snug fit and can be attached backwards for storage. ...Supports recommended for attachment ring.
thingiverse
Lens hood for 70-210mm Canon FD. Fits 70-210/4 and likely others with 58 mm filter ring. Roughly modeled after Canon BT-58. Snug fit and can be attached backwards for storage. ...Supports recommended for attachment ring.
thingiverse
This is a remix, but unfortunally I can't find the thing from the original designer. ... This lens hood was modified to fit a canon FD 50mm f1.4 lens. ... It's a tight fit, so there might be some sanding requiered.
thingiverse
...If you'd like to connect an FD lens to GuerillaBeam, I'd rather recommend an adapter to an intermediary lens mount. Focus to infinity can still be achieved this way, by attaching to the shorter light side of GuerillaBeam and using an extension tube.
myminifactory
This is a cap for a lens CS II 8mm 1:35 (Samyang model). It fit perfectly the lens. ... It could be used on another lens model.
thingiverse
A very simple lens cap. ... Source code: https://github.com/TomyCesaille/lens-cap blog post: https://jorislacance.fr/blog/2021/01/14/bahtinov
thingiverse
Lightweight and easy to print lens caps. ...Some sanding on the joints might be necessary for inaccurate prints. For more information and also STLs for other lens diameters visit: https://windfish.ddns.net/projects/normal/lens_cap/project
grabcad
Looks easy, bright, unique. ...Sense of the idea: do not lose the lens cap, I mean, it remain on the lens.
thingiverse
designed in Fusion 360. ...quick and easy. It is a very Basic lens Hood. printed with filaflex Filament. ...it fits very nice over the Focus ring
thingiverse
Canon FD / FL simple rear lens cap - Smooth surface - No writings 2% oversized to compensate PLA retraction STL exported full resolution (smooth curves) 3D designed: 1.2mm thickness / 1.85mm tihcker bottom (standard 0.8 wall print) Minimal supports...