Ultimaker XY Calibration 3d models

... 20 units. Emboss Height is precisely 0.5 millimeters. Tower Height measures 110 millimeters. Height Increment is adjusted in steps of 10 millimeters. Machine specified is an Ultimaker temp model. ...Temperature Increment is raised by 2 degrees.

I designed a clip that keeps a cover securely on the front of my Ultimaker 3, ensuring an ambient temperature while printing ABS and other plastics prone to warping. The cover I used is an IKEA storage lid held firmly in place by the pressure of the...

ich mache alle Bohrungen mit einen Handbohrer (nicht elektrisch) ______________________________ englisch: (deepl translate) Hello, I bought a used defective Ultimaker this I have already well renewed. one of the belts was very loose so I have me a...

Cheap and easy way to enclose an Ultimaker 2 is using this storage tote. It's not perfect, but helps maintain a steady temperature. I used Hefty 16-5 Gallon Holiday Tote with Latching Lid from Lowes. Print off four brackets and that's it. ...The...

This is an upgrade/mod for Ultimaker or any belt-driven gadget, totally. My initial version was closed and identical to the belt buckle, but then I realized the complexity in mounting it to the belt since it would have required attaching the screw...

Kids could choose their favorite letter and print it using an Ultimaker within minutes; printing durations varied from 2 minutes 19 seconds to 5 minutes 43 seconds. Even the Dutch royal family appreciated this unique design. Learn more at...

... using an M6 threaded rod or print them; washers between moving parts are recommended but optional. Print settings: 0.1mm layer height, 1.2mm shell thickness, 20% density, 70 mm/s print speed, 220°C nozzle temp, and 100% flow rate for your Ultimaker.

You can find our comprehensive print and assembly guide at https://ultimaker.com/en/resources/20399-airplane-model. Specifically, note that only a left version of the main wing and tail wing are available as STL files; to create the right version,...

Mount an E3D V6 hotend onto your Ultimaker 2 or 2+. Double fan duct for 30mm fans, with each fan being only 5mm high to prevent interference from the heated bed clips. To secure the fans in place, use a small self-tapper. The distance between the...

Cheap and easy way to (somewhat) enclose an Ultimaker 2. It's not perfect, but helps to maintain a steady temperature. I used this storage tote: https://www.lowes.com/pd/Hefty-16-5-Gallon-66-Quart-Holiday-Tote-with-Latching-Lid/50261173 Print off...

... the edge or too close to the wall behind. ...This can cause the filament spool to get caught.\r\n\r\nThese simple feet attach directly to the desk and sit snugly inside the base of the Ultimaker, holding it firmly in place without being visible at all.

This text describes custom feet created for an Ultimaker printer. The feet have a sloping design to enhance their visual appearance and are designed to fit securely onto plywood. They offer stability and elevate the printer off the table, improving...

... facilitates secure attachment of the rods to the pulleys from within the frame's interior, eliminating the need for end caps with friction-inducing properties. The concept behind this innovative design was pioneered by Ultimaker in their UM2 model.

To check the bed level on an Ultimaker, use a digital caliper like this LCD Digital Tread Depth Gauge (0.0005 inch/metric). Start by drilling 6mm bolt holes for easier access. The depth gauge fits into the holder and is extended over the bar to reach...

... I've kept those old ones in case you need them, though they don't quite match the look of these newer versions. I'm excited for you all to use and appreciate my design, and I believe it will work seamlessly with any printer, not just the Ultimaker.

This accessory replaces the wooden end of your Ultimaker, fitting inside the body for enhanced convenience. It allows simple attachment of two M3 nuts, eliminating the need for twizzers or nut holders during assembly. The central hole is slightly...

I modified Daid's Ultimaker feet design because they were too boxy and didn't sit high enough for my liking. To improve them, I elevated the design slightly and rounded off the corners so they wouldn't catch on things as easily. This new version...

Experience a better belt-tightening with the Ultimaker belt tensioner 5000, which replaces and outperforms its predecessors, including models 4000, 3000, 2000, 1500, and 500e. Tighten your belt efficiently by following these instructions: Remove...

This part works flawlessly with the Ultimaker bed, especially after upgrading the original lead screw and bolt with high-standard ones, such as standard lead screws and industrial-grade nuts. Print out this specific piece first and secure those new...

Print Settings: Printer Brand: Ultimaker Printer Model: Ultimaker Original Rafts: No rafts needed, as prints face down without any issues. Supports: No supports required. Resolution: Set at 0.15mm for detailed prints. Infill Percentage: Printing at...

This bracket, suitable for both left and right sides of an Ultimaker, accommodates IKEA's Ledberg LED-bar series. Each bracket features a 2mm hole for easy mounting. Additionally, it can fit LED strips onto 6mm thick plates. Notably, these brackets...

This is a simple PTFE Tube clip for Ultimaker printers with dual or single extrusion. Used for 4mm PTFE tube (1.75mm filament). The clip fits very tightly, leaving the tubes securely attached. Designed with 1.6mm wall, print with a 0.4mm nozzle with...

To reduce noise from my Ultimaker in a shared room, I used old springs to create dampers that uncouple the 3D printer from its wooden desk. These dampers significantly decrease sound levels, especially during high accelerations. In fact, photos show...

Snap on these standoffs to your Ultimaker to keep your work surface and printer safe from scratches. They also provide enough height to mount the power supply to the bottom of the machine, greatly reducing its overall footprint. These guys are quick...

The attached 3D models were created by Liz Arum of Ultimaker Education using the Morphi app (www.morphiapp.com) as part of a collaborative project with Ultimaker and Morphi to teach 5th grade students at New Lab in Brooklyn about 3D Design + 3D...

... basically good to go. ...The case screws together with M3 screws. Drill holes in your ultimaker and attach it using the little flanges. EDIT Oops, looks like I had the wrong pin diagram. Fixed now. ...Sorry guys</p> Category: 3D Printer Accessories

Benefits over the stock holder: - Easier to load filament - Can handle 1kg spools - Easy to see how much material is left - You don't have to pull you printer out every time you have to change filament - Fits all Ultimakers ( unless the ledge is...

This was necessary due to some issues that arose during testing - the original design turned out to be a bit too tight, especially when installed on the Ultimaker 2. Below you'll find a detailed guide for installation: Printed with a vibrant and...

This innovative creation consists of three expertly crafted parts: the latch and centering plug, inspired by eckerj's original design, and a custom clip specifically tailored to fit perfectly on the body of the Ultimaker 2. Please ensure that you...

It prints as three separate parts: the body of the printer, the extruder with the x and y axes, and the front panel with the Ultimaker logo. Insert the front x-axis rod into the back of the Ultimaker panel (so that the extruder nozzle is on the left...