Wire Strain Relief for Printrbot Simple Metal Heat Bed Modification 3d models

I feared yanking the power cord hard enough to pull the wired from the power supply. ...Mounts in the the 2020 extrusion channel nicely with a M3x10 screw and a drop-in M3 T-nut.</p> <p>Minor update.</p> <p>Magenta (thought it was more red) print was...

This fan shroud is tailored specifically for use on the Printrbot Simple 1405 with an E3D v6 Hotend. Theoretically, it also works seamlessly with the Ubis, but I can't confirm whether it will align correctly. A revised standard version (redone) is...

Slightly modified Printrbot Metal spool holder - shorter shaft and a smaller bottom lip for better interaction with the spools that I have.

20% Infill Screw holes for #6 drywall screws

Printed with PLA and designed for a snug fit onto the XAC. Fits micro, mini, USB C and USB A cables. ...USB B cables are too heavy of gauge.

... while playing Drop Dead, so this clip should help prevent that from happening again. The clip fits snugly over the plastic part and the velcro strap on the back of the headset. The clip was printed in gray PLA without any need for support material.

In the center, a section is reserved for the nurse or doctor's name to be inscribed above the line, while their rank can be noted below it. The design ensures that there is sufficient clearance for the ears. The curved edges facilitate quicker...

A designated section at its center is reserved for the nurse or doctor's name to be written clearly above a line, while their rank can be noted below. Its height ensures that there is ample clearance for the ears. ... The curved edges not only...

However, I became concerned with the bracket sticking out and getting caught on something, so I redesigned the piece to be print without needing support and using a right-angle mini USB cable for a lower profile. ... Both are designed to allow the LED...

The mount threads directly into the conduit hole of the charger, providing a secure connection for the 220V input cable. Mounting requires one 6mm bolt, while clamping the cable is facilitated by two 5mm bolts. ...This design ensures a stable and...

... mechanism to secure it in place. ...And please don't suggest that simply tying a knot would suffice, as 3D designers strive for more elegant solutions. ... I later created an updated version with an enclosure: https://www.thingiverse.com/thing:4416629

This accessory is designed for compatibility with the QU-BD One-Up extruder; however, it can also be used on other printers featuring an exposed stepper motor or a flat surface. ...The attachment is securely fastened using 2.5mm zip ties.

Remix of a very useful printer mod for the FLSun Kossel, but with a thicker build and improved fit to the bowden tube. ... Print Settings Printer: FLSun Kossel Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: ABS is preferred due to size...

... under lots of stress. ...This is just for emergency case, maybe stumble over the cable.&nbsp;It is attached with double sided tape with ~1mm thickness. Works as expected.&nbsp;</p><p>Best printed on the small edge. ...Support probably not needed.</p>

To address this issue, I adjusted the top to its minimum position and moved the Ziptie attachment right up to the cable, allowing for a secure tie-in at its strongest point near the base. Big thanks go out to the original creator of this design -...

A side benefit is the cable now comes out directly behind you so I am now less likely to step on it while moving side to side. I based my design on a part made by Reddit user Aquacide and added the channels for the cable and cable ties. Assembly is...

Cable saver for index. I made this after my cable started going bad. So I made this. Side effect is that it squished the current cable enough to use until the new cable gets here. This should in theory reduce the radius of the cables bends coming...

My design was based on a part created by Reddit user Aquacide and featured channels for the cable and cable ties. I incorporated these channels into my own design to ensure seamless assembly. Assembling this accessory is straightforward. Simply...

You'll sacrifice roughly five millimeters of printing area along the Z-axis.

At the same time, I ordered a new wiring kit from AliExpress that had two black and two red wires connected to the bed along with a specialized fitting into the wide bed-connector. 28-09-2019 : I recently discovered my blueprint was too tall for my...

A simple EBB36 CanBus Board Mount with Cable Strain Relief for the Orbiter v2.0.&nbsp;It's designed to be printed in ABS, as the little LDO motors get Hot, and to be attached via Female-Female M3x20mm Hex Stand-offs.&nbsp;&nbsp;The EBB36 board can be...

... and by extension stress on the cable and its connections. ...This strain relief support is a simple “cable saver”, turning the tide of the war gravity is waging against your consumer electronic signal carrying devices.Use (2) M3x10 screws to secure.

To enhance the CTC 3D Printer's heat bed performance, I added a riser/spacer that increases spring loading by 3mm. This accessory fits springs with dimensions of 10mm width and 6mm hole size. ...It was printed with specifications of 25% infill, 3...

Customized Version of https://www.thingiverse.com/thing:779559 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=779559 Instructions Using the Following Options: Guide Arm = 1 Z Rod Bearing Length =...

Customized version of http://www.thingiverse.com/thing:779559 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=779559

Human: Customized Version of Thingiverse Model 779559 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=779559 Instructions Using the Following Options: Lip Inner Extra - Set to 5 Units Cuts Per Revolution -...

I'm integrating the OctoPrint into my Printrbot Metal Plus. I'm using a Raspberry Pi Model B+ with a 12" Pi Camera Cable. The extension arms are adjustable, secured and tightened using M3 screws. The case is attached to the PrintRBot via the bottom...

This is the strain relief I designed for the Panasonic FZ-1 3DO. It's intended for production on a resin printer. This strain relief fits a two core UK or European 230-240v AC cable and can be secured inside with a tight cable tie. You would mainly...

This is a replacement connection cover with an added strain relief for the VGA cable used to carry the connections from the controller board. Remove the OEM Cover and replace with the printed one using M3 x 0.5 x 10mm long cap head socket head...