Wire Strain Relief for Printrbot Simple Metal Heat Bed Modification 3d models

This is a replacement connection cover with an added strain relief for the VGA cable used to carry the connections from the controller board. Remove the OEM Cover and replace with the printed one using M3 x 0.5 x 10mm long cap head socket head...

I got tired of aligning my Fulament PEI plate to the Printer bed, so I designed one of these for my printers. It Works really great and even has a Strain relief. Share the love! https://www.youtube.com/shorts/dsJgboF8cYI Good info!! Press the...

OpenDive 3d VR Goggles for Small Printer (Printrbot Simple). Printrbot Simple can make 10cm10cm10cm. So, I have devided the frame. ...(L,R)http://youtu.be/MjnG8jHp40M Original Source from http://www.durovis.com/opendive-howto.html

* None of the cables need to be disconnected, they can be inserted through the slot in the back of the strain relief mount. The strain relief mount was based on https://www.thingiverse.com/thing:4717506. * Wire tying the cables to the support keeps...

None of the cables need to be disconnected, they can be inserted through the slot in the back of the strain relief mount. The strain relief mount was based on https://www.thingiverse.com/thing:4717506. Wire tying the cables to the support keeps them...

For an original Printrbot Simple

To rectify this situation, I designed a small piece that secures the power cord to the machine's bed frame using a simple plastic clip. It will be necessary to drill two holes in the bed frame to attach the piece securely. ...Recommendation: maintain...

Sidewinder has no cable strain relief this can cause failed prints or worse burning connectors. This is a simple, light, but effective way to clamp the X ribbon cable, just reuse the existing screws, and instal without need to remove the ribbon...

Modded the Strain Relief-Cover to fit with the dualFPC-mod. ...Will probably not work with standard Cables.

... from the same company. The jack connects to a compatible power supply I have for a small rotary multi tool. It would be possible to power this from the heated bed circuit on the printrboard, but for now, the separate power supply is simple enough.

If printing two panels, glue them together, then attach the flange of one strain relief to the through-hole of the faceplate. Secure the assembly inside the box with the strain relief on the interior. Lastly, fasten the other strain relief half to...

This DIY modification makes adjustments possible through three-point adjustment screws that attach directly to the metal plate from behind. There are also two adjustable clips placed on the front for precision control. ... One detail is where we...

This mount, suited for Printrbot LC PLUS, provides easy leveling of the hotbed and requires three M3 4.5mm or longer screws, accompanied by three M3 nuts. Assemble the sprints loosely to avoid tightness issues. ...Note that an update from April 14th,...

One major change from the original design is the mounting hole distance of 30mm, allowing compatibility with the 40mm fan shipped with the PrintrBot Simple 1310. In the attached picture, you'll see the PrintrBot 1310 upgraded with aluminum extruder,...

I based this design on the mdkendal "Prusa i3 Mk2 Strain Relief for X Motor" found at http://www.thingiverse.com/thing:2025087. My inspiration came from MartinMajewski's rework of his Prusa i3 Mk2 (http://www.thingiverse.com/thing:1837853), which led...

Cable strain relief for Stockman59's Hero Me Gen5 mod for the ender 5 plus with Microswiss DD. Use M3 x 8 or 10mm, not sure which ones fit. Has 2 slots for small cable ties to thread through. ...Print on its back (so the curved surface where the cables...

This strain relief support is a simple “cable saver”, turning the tide of the war gravity is waging against your consumer electronic signal carrying devices.Use two (2) M3x10 screws to tighten. It's an interference fit, which means don't give it 10...

Simple combination of the Logitech C270 camera mount remixed lower by martsl, and the X-Motor Cable Strain Relief by mdkendall. I literally just spliced these two models together. To print the single part version, you will need to add supports. ... A...

This is just a simple wire holder for the extruder and hotend wires that come out the back of the Sooway SW-200 and similar 3d printers. I've noticed these wires sometimes get caught on the left rear bed adjustment knob and can cause it to come...

It is based on the Cupcade project but has been heavily modified to be printable easily on a Printrbot simple metal 3D printer. ...More info on http://www.gamoover.net/Forums/index.php?topic=32838.0 some videos : - https://youtu.be/bTUZjV4y_7k -...

All this movement repeats together with the X-carriage, making common sense dictate that a strain relief is necessary to prevent wiring fatigue (breakages, short-circuits) and the typical disastrous consequences. It also makes things look slightly...

Strain refill for DN32 tubes, none exceeding that specification.

To upgrade your Printrbot Simple Metal 1403 to a 10x10 print area for under $75, start by printing the shorter x rails on a 6x6 Printrbot Simple Metal (orient them diagonally and they'll fit). Next, print the 4 inch y axis extension. Order 8mm rods...

This particular model remains compatible exclusively with Jon's 208 bed ends; for different size configurations, feel free to make special requests or ask about adjustments to optimize performance further, as scalability is an easily achievable...

... MKII. ...The second file is half of the cable strain relief system. Should be a snug fit. It was made in a hurry for a pal who was building his practice/demostudio and I failed to take photos. ...I'll go by his studio one day and take the pics...

Hello all out there , Here is a proposal for a cable strain relief for ender 5 plus printer and micro swiss direct drive. The thing is mounted of threaded hole left free on micro swiss support . It print easely upside down. Edit 23/12/2020 : ...

This modification is designed to tidy up the Printrbot Simple Metal's 1403 finishing touches, while also serving as a mounting point for both the 30mm fan and the Printrbot LED module. ...It should securely attach itself to the Ubis 13s hot end.

... may not last long enough. ...Two versions are available: Original: Identical to the original from Printrbot Spaced: Holes for M3 16mm screws have been adjusted for better outcomes. ... Instructions: Print: 2 perimeters 50% infill 0.1 mm layer height

For reference, this design originated from the original Simple files available at printrbot.com/2013/08/01/printrbot-simple-files-are-available-non-commercial/. To print this part, use PLA at a 0.2mm layer height. Some fine filing might be necessary...

I liked the look of PearlGreyMusic's Hybrid Modular Spool Roller and I needed to replace my old spool holder so I whipped up these parts to mate the spool holder with my Printrbot Simple Metal. I used assorted M4 screws that I had, but this matches...