Yellowfin Tuna 3D Model with Poses 3d models

Customized Version of Thingiverse Object 41274 Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Using the following options: 03_knob_height is set to 16 41_height_of_cylinder_indentations is 15...

Now find a screw that fit the thing on the photo with the yellow light, that is not too small to fit the printed thing, if its too long you can use a spacer like me (there are 2 hole only 1 will be usefull. Unscrew the lead screw from the motor,...

... it easier e.g. to push a button from the outside - Conversion modules between the large and small diameters ## Precursor of this Design This design is inspired by https://www.thingiverse.com/thing:2627220 and strives to remain compatible with it.

Also, make sure the sight is on top, and the channel lines up with the plunger tubes air hole. The next step is to cut 40mm of 17/32 brass tube. Make sure all the rough edges are sanded smooth and a dart can slide in without catching. Test fit the...

This incredible ability is made possible by the billions of neurons that make up the brain, each one communicating with millions of other cells through electrical impulses. As a result, the human brain is able to perceive, process, and respond to its...

-- [English] -- This is a support for electronics based on an Injora chassis (copy of SCX10) with the engine in the front It is carried out in several parties in case it breaks in one place. In addition, thanks to the removable support system, it...

Make sure the orientation is correct with the front of the middle part having the two holes for the knob and aux port. Once it is slid in place just us some glue to hold it in place. Next put the speaker drivers into their designated holes and use 4...

This cover will work with any of the three versions of the case:Case W/ HC-SR04 https://www.thingiverse.com/thing:3177147 or https://www.prusaprinters.org/prints/8493-case-for-adafruit-animated-eyes-bonnet-for-raspberCase W/ US-100...

Yet many are struggling with the basic skills or know how. Secure Supplies makes it easier to find such information and thus reach more builder and Students of the rapidly growing industry. #shorts #shortsvideo JOIN US HERE =...

(G1 E100 F100 ) measured and found it really extruded about 104mm (measured with an ruler) 192x100 gives 19200 steps.. 19200/104 is about 184.62.. M92 E184.62 M500 would have fixed this on an normal printer.. but since you cant save to eeprom you...

So she began pilgrimages in secret to many of these sites, hoping to cure the afflictions and curses over them with the love of the Moon Glanbeli. Though it seems that what she wished for did not entirely come to fruition, and though small outposts...

My own personal version has a 0.5mm carbon fiber sheet on its bottom which though I doubt adds any real degree of strength (0.5mm is almost paper thin and can be easily cut with normal scissors) it does offer a degree of protection and definitely...

The human brain is a remarkable organ that continues to fascinate and inspire us with its incredible abilities and capabilities. ...As scientists continue to study it, we are gaining a deeper understanding of its intricacies and complexities, leading...

The problem actually is not with the batteries but the calipers itself as they only turn the screen off when the OFF button is pressed so a normal switch would also solve the problem but why not take it a step above and solve the problem of changing...

I used a laser engraver to etch these areas, but a firm hand and some time with sandpaper should give similar results. The surface just needs to be roughed up a little to promote a better bond. Magnet: Prep: Sand one face of each of the 8 (initial)...

... Make sure you install the base in the correct position so that the button lines up with the side of the light switch on the lamp fixture. Gently slide each lithophane into the grooves from the top of the frame. Make sure they seat against the base.

However, while you can absolutely use saddle clamps, and star pickets with twine/wire to anchor each end of the arched conduit, connectors to make better, or more complex designs aren't available, or aren't designed for load bearing stresses and...

It should fit with any other Mclaren F1 GTR made by Hotwheels. If you plan to use it for the British Horsepower set Gulf Mclaren F1 GTR, I have written how to colour swap to match its livery colours too. If you wish to have a display base tweaked...

... far-reaching consequences for the entire body. By understanding how each system works and how they interact with one another, we can better appreciate the intricate complexity of the human machine and take steps to maintain its optimal functioning.

If you suffer with pore bead adhesion or warping I would recommend using any epoxy putty to fill any gaps you might find between the pieces before painting. the stock attaches to the pistol via the removable pin hole on the rear of the grip and the...

With its 1-meter length and motor mount at one end, this slider provides smooth and precise movement for capturing stunning footage. Check out the sample video here to see it in action: https://www.youtube.com/watch?v=2xG3Ls4m5AI To build your own...

You may want to experiment with this depending on your printer's characteristics. Once all the parameters are in, uncomment all the module lines including the translate and rotate function and you can render the knob as a whole. To compile for .stl...

This is Intercooler Kit for the EJ20 Subaru Engine (http://www.thingiverse.com/thing:2451310). My finished project : https://www.thingiverse.com/make:719585 Print instructionsPrinter Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:...

The provided STL files are matching my Cube Race One 2015 with 17.1mm diameter for the seat tube strut and 20mm clearance for the strap of the Sigma Blaze. The bracket is certainly not perfect, but it does its job so far. Should you have any bugs...

A tablet was also found consisting of an unknown material with a sacred text on it. As it turned out, the obelisk consisted of the same material. Unitologists for another hundred years could not read the letters until they deciphered the runic text...

The DIY head tracker is a Github project by Cliff "dlktdr".A holder and the housing cover of my design are screwed to the side of the googles strap eyelet.The actual head tracker is pushed onto the housing cover from above.When the tracker is not in...

Next glue the large curved back and the Ts making sure every thing is aligned with the slider slots and in position. I highly recommend getting used to this design and where the parts go before ever pulling out the super glue! The bottom is the...

Racing Wheel Design presents an I-FLAG and gear indicator engage with or without cap plus removable brackets in all directions to attach it to any simracing setup. Race list: 1: arduino nano ...

I print mine with 0.16mm. - **Mount**: Optional. I designed it for this carrier. But any 18mm sensor mount will work. **Non-Printed Parts:** ...

its unfortunately rather tricky to get a perfectly horizontal or vertical tool head plate in certain heights (as the combination of teeth angle do not add up perfectly to 0dgr or 90dgr at all heights) Come to think of it I could have designed the...