abus granit detecto x plus 8000 3d models

Quick and dirty update to the cable chain tray for the X axis. ...Allows the trays to be used without the need to relocate the Y endstop. This replaces the right-hand (from front of printer) piece of the X axis tray.

The X carriage wiring that comes stock does not have very good cable support. I designed this very simple mount that holds the cable loom in a vertical position. ...All that is needed to mount is QTY 2: M4 x 12mm screws QTY 2: M4 T Nuts

... and Y axis, utilizing original switch board. ... X-endstop is lifted upright to make room for cable holder on MicroSwiss NG since original one does interfere with secure screw to hold holder in place (Halfway screwed to opening for front shroud screw.

... prevent this issue, I added a snap-on cover that provides stability and security. The snap-on cover for phones without cases is available in two files: tesla_x_phone_charger.stl and tesla_x_phone_charger2.stl, which includes a version with a case.

This revised version of the iconic iPhone stand has been reimagined to seamlessly integrate with your phone's protective cover, specifically tailored for the sleek and innovative design of the iPhone X.

The standard X-axis limit switch placement isn't exactly rock-solid. ...This mounting bracket adjusts the switch's position, ensuring a stable connection with the print head carriage instead.

For the parts to be stronger, print orientation should be like this without any supports.BOM2 x M5x10mm Socket Head Screw2 x M5 T-Nuts1 x M8x30mm Socket Head Screw1 x M5x30 Hex Head Screw1 x M5 N-Lock NutIn order to keep the belts perfectly align...

To use this kit you will need: 412x305mm Polycarbonate sheet (3mm thick) 4 x M5x16mm countersunk screws5mm drill bit (for the polycarbonate)2 x 10x3mm magnets (if you wish to use the magnetic closing on the doorPrior to drilling holes in the...

It's a modern take on the "invincible" fight jet from the Macross Plus universe. Unfortunately, there isn't a free version available online yet. I'm sharing it here and hope it will meet your collection needs. The model is 1/60 scale, but if you set...

It is a modern take on the "invincible" fight jet from the Macross Plus universe. Unfortunately, there isn't another one available online that's free. Here it is and hopefully it will add to your collection. The model is 1/60 scale and if you set...

A more robust alternative to the original X-axis belt tensioner is available for use. ...I suggest pairing it with this belt holder https://www.thingiverse.com/thing:4024940 The other end of the belt can be secured in place by screw and cable tie, as...

... screws (M3). ...This tensioner is suitable for the X and Y axis. If you liked the part and it fulfills its functionality, I would appreciate a small donation. To do this, press the "Tip Designer" button on this page or in my profile. ...Many thanks!

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

After upgrading to linear rails there was nothing to trigger the endstop so I re-designed the x-axis endstop mount. designed and oriented so that the metal clip naturally rested on the micro switch rather than against it, works in conjunction with...

Wanhao X Gantry Upgrade with LM8UU This upgrade significantly enhances stability and reduces deflection from the standard ends and z wobble. When assembling the upgrade: LM8UU - spacer - LM8UU - cap Double-check your bar spacing, which should be...

Wanhao X Gantry Upgrade with IGUS Bushings Majorly Enhances Stability and Reduces Deflection from the Stock Ends and Z Wobble. ... When Assembling: Bushing - Spacer - Bushing - Cap Double Check Your Bar Spacing, Either 44mm or 45mm; There's a File for...

......After a thorough search, I was unable to find an available LED strip holder that would fit perfectly on the i3 Plus, so I designed one myself. This custom-made holder should accommodate any standard width (~11mm) LED strip without needing adhesive.

This is a simple mounting bracket for two Trianglelab 8 diode smoothers, allowing them to be connected to X, Y, and/or Z motors with ease. To install it, simply place one unit next to the motherboard using double-sided tape, while positioning the...

I've also added X-axis tensioning into the design which again has advantages in comparison to doing it long the length of the belt. It gives much more subtle adjustment. ...In concert with working bearings, it allows tighter settings with better levels...

Made from scratch but based off the original printed dimensions of SpragClutch's dry box side holder for the X-Max 3. I'm able to use the same stock tubing however results may differ. Made to use with the rubber feet. I also didn't take the time to...

This compact storage container boasts three secure ports at the rear for simultaneous charging of Estes Proto-x and Hubsan Q4 Nano Quadcopters. Simply draw the retractable drawer towards you, exposing the charging ports at the back. You can rest...

My second update is the cable chain for the X axis. My problem is that, being in a wheelchair, my fingers have no strength and I didn't want to have to let go of everything to insert one by one into each link. ...That seems unnecessary to me and so I...

To get the mount for only 2 smoothers, download "XY_Mount_V3_Letters.stl" or "XY_Mount_V3_No_Letters.stl." For 4 smoothers, download "TL-Smoother X _ Y _ Z Mount V2.1..stl." The updated version 3 was made on April 6th, making the mount slimmer and...

If you are using a smaller iPhone model, such as the X, you may need to print two small extensions on either side of the holder to prevent it from tilting or falling over. However, I have found that an X fits perfectly within this holder without...

I also added X-axis tensioning into the design, which has its own set of advantages over doing it along the length of the belt. It gives much more subtle adjustment. When combined with working bearings, it allows tighter settings and better levels...

Somehow the printer has a 310x310 bed and the X and Y limit switches line up to the edges of the bed.We cannot utilize the full 300x300 bed size if 0,0 is at the edge of the bed. This is a failure of the written firmware to effectively utilize the...

Somehow the printer has a 310x310 bed and the X and Y limit switches line up to the edges of the bed.We cannot utilize the full 300x300 bed size if 0,0 is at the edge of the bed.  This is a failure of the written firmware to effectively utilize the...

You will need to run the X axis switch wire with the other hotend wires. Small price to pay to get the homes the same! Note: I have not set my FT5 up with this yet but there shouldn't be any issues that I can see. UPDATE: 4-15-19. Edited the Y axis...

You will need to run the X axis switch wire with the other hotend wires, a small price to pay for getting homes the same. Note: I have not set up my FT5 yet but there shouldn't be any issues that I can see. UPDATE: 4-15-19. Edited Y axis endstop on...

I have designed a ventilation system for the Xbox X series, which consists of a 120mmx 25 top fan adapter, a base with a dust filter, and two little back filters. I recommend printing the base with supports as shown in one of the images the...