abus granit detecto x plus 8000 3d models

The x-axis carriers in this set have been modified to use readily-available round TR8x4 POM nuts (same size as Prusa Mk3 POM nuts). I designed these replacement parts with three goals in mind:Tighter grip on the extruder carriage linear bearings for...

This is a printable set of replacement Z axis bearing carriers for the X axis gantry assembly for the Anet A8 and Anet A8 Plus 3D printers. These printers ship now with injection molded carriers, which work fine in these printers default...

Apparently, the split in the original injection molded carriers offered enough leeway that I hadn't encountered those problems for as long as I've had the A8 Plus.Another change I made was to the "X_Carrier_Right_V1.1TBS.stl" file by adding a...

Top covers are installed on the Z-axis of the upgraded BearX model for the ANET A8 Plus 3D printer.

This is a belt tensioner for Anet A8 // A8 Plus that uses the same X-axis group. Start with the tensioner from https://www.thingiverse.com/thing:2934446. I'm using a self-modified version of a toothed idler by GonzoG, which incorporates an...

To overcome z-wobble, I made key modifications to the x-carriage mounts to accommodate a v-slot wheel. To make room for this upgrade, I relocated the mainboard's housing using a 2020 corner. All necessary parts are included in this design. After...

These panels are used to mount the AC Infinity Airplate T3 and control panel to a Qidi iMate-s or X-Plus. They replace the magnetic removable side panels. This gives one thermostat control of the temperature inside the print area. Tested on iMate-s.

... Please leave a comment if that is not the case. Finally, the part will not interfere with the tightening knob. The component is compatible with : • Anycubic Photon Mono X 6K; • Anycubic Photono M3 Plus; • Anycubic automatic resin feeder.

This is a hood cover for the qidi-X-Plus with closeable 50mm hose connector and screw mounting. For mounting it is necessary to melt 3 threaded inserts M3x5,7 (number A and B). The two inserts under number A will still protrude approx. 2mm after...

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace extends your Anet A8 Plus in the X and Y directions by 40mm, providing stability to the frame and sufficient space for a 330x330mm hot bed surface....

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace is ment to extend your Anet A8 Plus in the X and Y directions by 40mm. The brace will help stabilize the frame and the added room gives you enough...

I originally printed prototypes using my Qidi X-Plus, which produced useable parts, but with all the support issues and material limitations (shrinkage, deformation temperatures when hot end is mounted), I found resin was best. The resin I used was...

In this process, you must attach a GT2 belt to a Printrbot Plus v2. ...To ensure proper fit, you should drill a fresh hole for the lower screw, allowing the belt to pass smoothly beneath it.

Print Settings Printer: Raise3D N2 Plus Rafts: Enabled - Yes Supports: Disabled - No Resolution: Set to 250 microns Notes: The resolution setting is irrelevant in this case. ...To achieve optimal results, select Vase mode when printing and use a single...

Still have 3mm filament that you want to use with your Printrbot Plus v2.1 with the Z-X Upgrade? This adapter replaces the standard baseplate (using Direct Drive extruder) with one that lets you mount the tried & true Wade's Extruder. I created this...

xbox series x case for orange pi boards.

Couldn't find a tensioner for the Wanhao Duplicator i3 Plus Mk2 (only i3 Plus, which has a different carriage design) so I made one. It has the correct standoff from the carriage for good belt alignment, and is low enough that it doesn't rub against...

iPhone X Owner Shares Exclusive Hands-On Experience Check out this incredible hands-on review of the revolutionary new iPhone X!

This is for the Ender 5 Plus with linear rails with a Micro Swiss Direct Extruder mounted. To mount the Switch you must thrill 2x M3 screw threads. I hope this Thing is useful for you UPDATE: V2 now available I had Problems with the...

To be used with Densium 4 Plus on the wooden part inside. Haven't tried it yet. Small bit removed on the bottom to fit in with the metal brackets. ... I like how clean this 3D printer is: https://www.treatstock.com/c/fusion-forge-3d

This is a remix of my X brace found here: https://www.thingiverse.com/thing:4133747 This X and Y brace is ment to extend your Anet A8 Plus in the X and Y directions by 40mm. The brace will help stabilize the frame and the added room gives you enough...

This design is an adaptation of my previous model, tailored specifically for use with a Phone 7 Plus, even when paired with an Apple or slightly thinner case - all without requiring removal. A normal microphone stand adapter provides immense...

With the help of the internet, I created a 1/60 scale model inspired by Macross Plus' "invincible" fight jet. Currently, there isn't a free online version available. Attached is an image for reference. If you adjust your printer settings to print at...

Mount this above your x-axis motor for a spot to zip-tie the cables.

* M5 X 40mm (DIN 912): Cut to a length of : * 30mm x2 * 25mm x2 The idlers will sit on the non threaded part of the bolt * m5 nuts x 4 * F695-2RS - 5 x 13 x 4 mm x8 You will also need to print the X and Y nema 17 mounts found here...

My Ender 5 Plus was extremely loud, so I changed all its fans. The loud one at the nozzle was swapped with a 40x20mm Cooltek one (very nice result) and so it did not fit into the normal metal duct. This one is designed in the same style, only...

Resolvi fazer umas capas de acabamento para esconder os componentes do eixo X. Se gostarem baixem e usem como desejar. ... Até mais galera!!

I added this pulley for reduce the resistance of spool. ...I used two bearings dimension D.19 d.10 x 5mm.

I added this pulley for reduce the resistance of spool. ... I used two bearings dimension D.19 d.10 x 5mm.

Modified and updated X end stop with a precise hole to steer the filament smoothly into place, preventing accidental releases that could disrupt print flow.