access port v2 3d models

this safe and friendly looking representation of a port access needle kind of resembles a bee.&nbsp;assemble with super glue, using part of a paper clip for the needle. ...Optionally, you can add 1/8th inch OD silicon tube</p><p><i>THIS IS A TOY MODEL...

90 DEG; STRAIGHT, 90 DEG. ...RIGH, 90 LEFT CONDUIT ACCESS BOX.

Access port for fabricated steel tanks - pdf format

Open ports, screw mount. ... PLA

I ride a motorbike to and from work, and need to use an access card to get into the underground carpark. I modelled this holder in Fusion 360. With a velcro strap, I can wear it on my wrist, making it easy to present the card and open the roller...

I have PoE hats on my Raspberry Pi devices and they run headless so I really didn't need any access to the USB Micro/HDMI/Audio ports. The middle piece should be printed with supports. When I printed the original's I did 15% density, lines,...

Another one from my city shoot. ...64 photos in agisoft metashape

Recessed hand grip &amp; chain link handhold

Remix from https://www.thingiverse.com/thing:3714695 to be able to access GPIO port and to more cooling from the bottom

This mod replaces the sliding locking mechanism, improving it, and giving access to charging port and headphone jack of the device. It is not a moving part, but the device can be removed just as easily by gently flexing the case. Fits the...

I modified this really nice case with : Remix of http://www.thingiverse.com/thing:1503651 1: access port to the power connection to the RPI 3, because I did not use the portable battery pack part of it, (for now). Later I will try to incorporate...

This does not allow access to the ports on the side of the TFT. After some playing around I have the mixed pieces angled just about right. This could be improved, but my CAD skills are lacking still. Marking this as WIP, will come back and try...

This does not allow access to the ports on the side of the TFT. After some playing around I have the mixed pieces angled just about right. This could be improved, but my CAD skills are lacking still.</p> <p>Marking this as WIP, will come back and try...

A remix of the Adafruit feather no-tab case with an updated USB-C port to replace the micro USB used on the previous Feather boards.

This is a replacement door for the back panel for the Atari 5200 for those looking to install Sophia 2 which has a DVI-I port! It takes some effort to take the old one out, and then pop this one in (takes a bit of effort). I printed with PLA...

This go pro holder is designed so that the charging port can be opened while the Go Pro is in it. I made this so that I could do long duration time lapse videos while GoPro is plugged in so that battery won't run out. ... Designed so that no support...

... model was originally created with Sketchup 8 and then converted to all other 3D formats. ...Native format is .skp 3dsmax scene is 3ds Max 2016 version, rendered with Vray 3.00 PLAZOLETA WHERE THE CONTROL OF ACCESS TO PUERTO DE SANTA POLA (July 2013)

This is a case for the XEM ACCESS CONTROLLER V2, no screws required to keep the board inside the case, it's designed to hold it in place by pressure for quick access when wanting to change the board pins.

Updated Coil for the xEM access controller v2. The original just wasn't working too well after using it for a while, so I've made some slight changes to it, mainly just changing how the fillet around the edge sits. The holes are designed for m3...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

An 8 port mechanical air raid/tornado siren. Rotor should be printed with 50 percent infill or more. Stator can be printed with 20 percent infill or more. Rotor Cap can be printed with 20 percent infill or more. Glue rotor cap on with hot...

Modified to allow easy access to the einsy-board. ...Additionally you can connect a cable to the USB on the go port. So you can hook a webcam to the Raspberry Pi Zero W. ...

I added an opening to access the charge port, for charging or to connect game controller as well as added points to attach a head strap/harness. Eye piece is at http://www.thingiverse.com/thing:773756 original version:...

I added an opening to access the charge port, for charging or to connect game controller as well as added points to attach a head strap/harness. Eye piece is at http://www.thingiverse.com/thing:773756 original version:...

this is made to be able to use my Cobb access port mount to hold my galaxy note8 cell phone. i use it for maps and digital dash. i use an obd link bluetooth scanner note8 has a case on in the pictures. I put some paper and glued it to one end to...

If your drone's motors use bolts instead of c-clips to secure the bell, then these landing feet might interest you. Makes cleaning and repairs in the field MUCH easier. Can be used with 16x16 thru 19x19 bolt patterns. ... UPDATED: Added 16x16mm...

I was having some problems with damaging the MicroUSB port on my Ender 3 v2, so I made this piece to prevent the cord from being able to be pulled sideways, which is what was damaging the port. There is a cutout so you can still access the MicroSD...

... pins. That's where this case cover comes in. Just remove the original AstroPrint Astrobox PCDuino v2 cover and use this one instead for full access to all the pins. ...(Running the arduino IDE or other languages to control them are up to you!)

... pins. That's where this case cover comes in. Just remove the original AstroPrint Astrobox PCDuino v2 cover and use this one instead for full access to all the pins. ...(Running the arduino IDE or other languages to control them are up to you!)

Case designed for the xEM Access Controller v2 with Cover Plate for the antenna. The holes are designed for m3 bolts (some are a loose fit for through hole mounting. The hole spacing is the same as the coil cover plate which can be found...