adafruit 3 5 3d models

Rasberry pi 3 + 3.5 TFT case Snap pi board into bottom ( without sd card in it ) then plug in TFT screen and snap on the top. ...and easy removal.

This is an update for 3 Hard Drive Disk (HDD) enclosures with a 3.5-inch form factor. Two identical copies of the design are required, ensuring perfect symmetry. ...Version 2 includes refined details and increased illumination.

The 3.5-inch hard disk offers robust support.

3,5 inch versionNo support or raft needed

Teensy case 3.5 with teensy hardware (not grouped)

AOS 3.5 immortal T and VTX antenna mounts

Runcam Thumb mount for AOS 3.5 frame

Simple pencil holder made of 4x 3.5" FDD.

Kettle 2.5-3-6. PLA 100% filled. ... Printed, works.

my prints for the flyfishrc vx3/3.5

Four 3.5-inch hard drives are stored.

------> http://adafruit.com/circuitplayground Adafruit invests time and resources providing this open source design, please support Adafruit and open-source hardware by purchasing products from Adafruit! ... This papercraft resistor calculator was...

Remixed the 4x 5 pin mount to be 5, 3, 3 mount. The wagos snap in nicely. Also added STEP files for each type of mount so you can create your own combo. Print laying flat as shown in the slicer screenshot. ...No supports needed

You'll be up and running in 15 minutes or less.Some quick specs:Simple I2C controlUp to 8 on a single I2C bus with adjustable address pins0.25°C typical precision over -40°C to 125°C range (0.5°C guaranteed max from -20°C to 100°C)0.0625°C...

You'll be up and running in 15 minutes or less.Some quick specs:Simple I2C controlUp to 8 on a single I2C bus with adjustable address pins0.25°C typical precision over -40°C to 125°C range (0.5°C guaranteed max from -20°C to 100°C)0.0625°C...

... enclosure, case, and base plate for the Adafruit Pyportal Titano. ...To secure it in place, you'll need four M2.5 screws, each measuring 14mm long, along with four matching hex nuts to keep the housing and Pyportal assembly tightly connected.

I sought out a case that would securely hold both the CLUE and the standard 3 x AAA battery pack, while also enabling effortless battery swaps without ever having to remove it from its casing. The result is now at hand. You can find the CLUE at...

A 3.5 HDD Stand Stackeable with one unique top and 3 options with different shapes.

The main difference is the difference in size, this is using a 3.5" Adafruit PiTFT touch screen instead of the 2.8" screen. I'm including the Fusion 360 file for anyone else to remix from this, or accomidate different parts. Parts used: 3.5"...

A Renault Loudspeaker Adapter designed to accommodate a 6.5-inch loudspeaker is compatible with the Megane Coupe 3, yet also suitable for installation in various other vehicle models.

http://www.thingiverse.com/apps/customizer/run?thing_id=1375996 Instructions Using the following settings: Tolerance set to a precise 0.25 millimeters Hexagon dimensions tailored to perfection: Largest hexagons set to 3 millimeters in size...

Enclosure for Teensy 3.5-3.6 with opened space for 8 THT pins in the middle and hole for reset press. Mounting holes made for M3 screws. If you find my designs useful, share with other, press a like. A tip for a cup of coffee is also welcome to...

Raspberry Pi 3 with a 3.5-Inch TFT Case Simply snap the Raspberry Pi board into the bottom of the case, leaving out the SD card for now. Next, plug in the TFT screen and then snap on the top half of the case. ...That's it - your device is now fully...

HDD 3.5 Mounting System for 2,3 or 4 hard disks. ... Print 4 copies for success

Here are the Adafruit Goggles, available at https://www.adafruit.com/product/2221 - a great solution for anyone who wants to wear their goggles without getting blinded!

Remix of https://learn.adafruit.com/qt-py-snap-fit-case

I modified the Trinket Bumper design created by ScottCher on Thingiverse, adapting it specifically for use with the Adafruit Trinket M0 board available at adafruit.com.

I am replicating the Adafruit Pixie 3W RGB LED (https://www.adafruit.com/product/2741) design for an ongoing project of mine...

... the top of this case to seal it from the elements and allow light transmission.  I hot glued the sensor to the case so it wouldn't slide around.Print SettingsPLA.3 layer height2 perimeters4 top layers3 bottom layersTotal print time=10minutes.

This is a water tray for the 3.5" Nepenthes pot.