adafruit esp8266 3d models
9243 3d models found related to adafruit esp8266.thingiverse
This is a super small weather station that holds 1 Adafruit ESP8266 Huzzah Feather, a .96" OLED (128x64) and has an external mount for the small DHT (Temp/Humidity) sensor. Now that I got all that off the breadboard, I'm hoping someone can link me...
thingiverse
... labeled (difficult to print) the second is smooth. The Adafruit HUZZAH ESP8266 slides into the base and the cover snaps onto the base leaving a nice piece. ... Holes in base provide access to both reset switches and the LED on the microcontroller.
thingiverse
Modular snap fit housing for Adafruit HUZZAH ESP8266 board using different sensor on their respective breakout boards. So far I have - DHT22/DHT23 - Si7021 (https://www.adafruit.com/product/3251) - HTU21D-F (https://www.adafruit.com/product/1899) A...
youmagine
These cases are compatible with the following Feather boards: Adafruit Feather HUZZAH with ESP8266 WiFi: https://www.adafruit.com/product/2821 Adafruit HUZZAH32 â ESP32 Feather Board: https://www.adafruit.com/product/3405 Feather ESP8266 Top Cover...
prusaprinters
These cases are compatible with the following Feather boards:Adafruit Feather HUZZAH with ESP8266 WiFi: https://www.adafruit.com/product/2821Adafruit HUZZAH32 – ESP32 Feather Board: https://www.adafruit.com/product/3405Feather ESP8266Top CoverSelect...
grabcad
A variation on the Adafruit Feather Huzzah ESP8266 Arduino compatible WiFi module. This variation envisions an external antenna option via the u.FL connector, instead of the PCB antenna in the original.The Feather modules are perhaps the simplest,...
thingiverse
... here: https://eckstein-shop.de/LiPo-Akku-Lithium-Ion-Polymer-Batterie-37V-2000mAh-JST-PH-Connector While I was at it, I also added a wall mount where the weather station can be dropped in easily. Thanks to Adafruit for this great project!
thingiverse
Feel free to contact me for updates if necessary For this case some hardware is required: 4x screw M2 x 4 mm 4x screw M3 x 25 mm The case above was printed in fillamentum "vertigo grey" https://fillamentum.com/products/pla-extrafill-vertigo-grey...
thingiverse
... Notes: I printed it without supports in 0.1mm mode and it worked fine, as it doesnt matter that the underside is a little rough. How I Designed This Designe in 123D including a simple Adafruit Huzzah ESP8266 breakout board
youmagine
Best used with male headers soldered top-side. Try using the asterisk cutout to organize if free wiring. Printing notes This case was designed around a 0.48mm extrusion width. This gives the features on the case a bit of added strength. If the case...
thingiverse
Best used with male headers soldered top-side (though now available with bottom cutout too). Try using the asterisk cutout to organize if free wiring. Printing notes This case was designed around a 0.48mm extrusion width. This gives the features on...
prusaprinters
<p>Best used with male headers soldered top-side (though now available with bottom cutout too). Try using the asterisk cutout to organize if free wiring.</p><h4>Printing notes</h4><p>This case was designed around a 0.48mm extrusion width. This gives...
thingiverse
I bought a ESP8266 Huzzah Feather and 3.5" LCD Featherwing from Adafruit and wanted a table top case to put them in. I designed the case just big enough so that the displayable area of the LCD is centered in the bezel. The top and bottom are also...
grabcad
Complete CAD Model for the Adafruit Feather ESP8622 including all SMD parts and decals.One version with pinheader and the other without.More Infos here:https://www.adafruit.com/product/2821
thingiverse
Code: https://github.com/dbarzin/FeatherDeauthDetector Hardware : Adafruit Feather HUZZAH with ESP8266 https://www.adafruit.com/product/2821 Adafruit Quad 2x2 FeatherWing Kit with Headers https://www.adafruit.com/product/4253 Assembled Adafruit...
prusaprinters
... I can't find a way to turn off the LED. :PYou need:Adafruit 1.2" 4-Digit 7-Segment Display w/I2C Backpack https://www.adafruit.com/product/1269Adafruit Feather HUZZAH with ESP8266 https://www.adafruit.com/product/28214x M2.5 6mm screws and nuts
myminifactory
Jumperwires enclosure for Adafruit Huzzah ESP8266.
thingiverse
Bracket for easy mounting an __Adafruit HUZZAH ESP8266 breakout__ board.
thingiverse
I was having a hard time reaching the buttons on an [Adafruit Huzzah ESP8266](https://www.adafruit.com/product/2471) so I made this little thing to make it easier to put the board into bootload mode.
thingiverse
Basic frame / standoff for the Adafruit Huzzah ESP8266 Breakout board (https://www.adafruit.com/product/2471). ...Just enough to get it off the workbench, but not impede access to the pins.
thingiverse
Jumperwires enclosure for Adafruit Huzzah ESP8266. This is my first 3D model and my first try with openSCAD. ...I've modified paolo68's source to fit my needs with the cost of flexibility of rows and pins.
cults3d
Jumperwires enclosure for Adafruit Huzzah ESP8266. This is my first 3D model and my first try with openSCAD. ...I've modified paolo68's source to fit my needs with the cost of flexibility of rows and pins.
thingiverse
Quick and simple sliding top enclosure for the fabulous Adafruit Huzzah ESP8266 module. I only needed access to the power and main serial IO so I provided access to just the end connections. You can re-roll the scad file to fit your needs. ... Drill...