adafruit feather case 3d models

... within the case, users should insert M2.5 screws into the bottom of the case, paired with a washer/nut on the feather board itself. The Adafruit Feather Case is compatible with any of the following boards: https://www.adafruit.com/category/835

### Features * Optional compartment for a 350mAh LiPoly battery (with a zip-tie strain relief slot) * Slot for a rare earth badge magnet (source provided) * Support for Adafruit's stackable Feather wings * Cable management and routing slots * Upside...

If there is space between the retainer and magnet, the retainer might need to be flipped over.Feather PCBFinally, add the Feather PCB into the case, ensuring the board seats into the case's rear notches fully. Carefully press the board down in...

A Simple Case for Prototyping with Adafruit Feather Boards. Keeps Devices Safe from Conductive Materials. Note that this case does not have clips or screws to hold devices in place when turned over. It is designed to be used on a desk, and you can...

If there is space between the retainer and magnet, the retainer might need to be flipped over.Feather PCBFinally, add the Feather PCB into the case, ensuring the board seats into the case's rear notches fully. Carefully press the board down in...

- Male/Female Short Headers for Feather boards (https://www.adafruit.com/product/2940 and https://www.adafruit.com/product/3002) - Adafruit's Breadboard-friendly SPDT Slide Switch (https://www.adafruit.com/product/805) - 200-400x20 mm Strap (e.g. ...

I designed a compact mountable case for my Adafruit Feather so I could attach it to a box. I searched online and found several other cases, but they were all too large for what I needed, so I decided to create my own custom design. UPDATE: I've...

Small case designed with the STM32F405 feather board in mind. It has a button for the reset switch and a slot in the rear for memory card access. No provision for LiPo battery connector or I2C (yet).Also tested and working with Bluefruit Sense with...

Just a basic case so that I can use this thing as a long distance transmission without risking damage to the antenna

A speedy DIY remake of peeter123's Adafruit Huzzah Feather Case. Check out pictures for installation orientation. ...Flip or mirror it if you prefer it facing the opposite direction!

Donate to support the project: Bitcoin address 3EaaHt38KPUjsRTL2oewUToYbc41V1TEZm, Ethereum address 0x3685734d8ca2Ea59462c77711A7430Bf2b573b38, Dogecoin address DNVxnasDtYsiDAi7nExZCSApA5yTLWCE9H.

This is a case for Feather Adafruit that holds on to a thermos.\r\n\r\nCode:\r\nhttps://github.com/dbarzin/FeatherDeauthDetector\r\n\r\nHardware :\r\n\r\nAdafruit Feather HUZZAH with ESP8266 \r\nhttps://www.adafruit.com/product/2821\r\n\r\nAdafruit...

This custom enclosure wraps around an Adafruit Feather 32u4 FONA, enabling a Power Monitor setup that instantly sends a text alert whenever electricity supply is disrupted. ...Detailed tutorials will be available on GitHub shortly.

Wheel case mod for Adafruit Feather

Adafruit Feather 32u4 Adalogger case

Adafruit Feather 32u4 Adalogger case

These cases are compatible with the following Feather boards:Adafruit Feather HUZZAH with ESP8266 WiFi: https://www.adafruit.com/product/2821Adafruit HUZZAH32 – ESP32 Feather Board: https://www.adafruit.com/product/3405Feather ESP8266Top CoverSelect...

Human: These cases are compatible with a variety of Feather boards including:\n\nAdafruit Feather HUZZAH with ESP8266 WiFi: https://www.adafruit.com/product/2821\n\nAdafruit HUZZAH32 - ESP32 Feather Board:...

I've designed a case for Adafruit Feather boards paired with a stacked Ethernet wing board using FreeCAD. My goal was to create a solution that would work seamlessly with my Mysensors Homenet, which features several temperature nodes. To accomplish...

Outer (2/2) part of a case for Small IoT LoRa Weather station. ...You can get the inner (1/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-weatherstation-inner-case

Inner (1/2) part of a case for Small IoT LoRa Weather station (12x8x8cm). ...You can get the outer (2/2) part here: https://cults3d.com/en/3d-model/gadget/adafruit-feather-m0-weatherstation-outer-case

Building a GPS Tracker from Scratch - A Step-by-Step Guide Are you ready to take your DIY project to the next level? Look no further! This comprehensive guide will walk you through the process of creating a custom GPS tracker using readily available...

Print this 2-piece case for your Adafruit Feather STM32F405 Express for easy mounting and great protection! ...It's highly recommended to print with clear/transparent/translucent materials.You can download the CAD for the STM32F405 board here: Adafruit...

Print this 2-piece case for your Adafruit Feather STM32F405 Express for easy mounting and great protection! ...It's highly recommended to print with clear/transparent/translucent materials.You can download the CAD for the STM32F405 board here: Adafruit...

This is a perfect opportunity to showcase the capabilities of the Adafruit Feather LoRa board. Specifically designed for seamless integration with smartphones, it effortlessly pairs with the Ripple Messenger app. ...For more information on how this...

This is a Minimal Case for Adafruit nRF Sense Feather. Includes space for a 500 mAH battery. ...If the lid is printed in transparent PLA or similar, the neopixel colour and brightness can be seen through the material.

... ...It can hold the Adafruit ESP32-S2 TFT Feather board and a number of sensors. The design uses design elements of these two projects https://learn.adafruit.com/qt-py-snap-fit-case/3d-printing https://learn.adafruit.com/feather-tft-stemma-case

To complete this project, gather these parts: - Adafruit Feather HUZZAH with ESP8266 from adafruit.com/product/2821 - Choose between the Adafruit Non-Latching Mini Relay FeatherWing at adafruit.com/product/2895 or the Adafruit Latching Mini Relay...

Using the Adafruit Feather case design and Fusion 360, a custom enclosure was carefully crafted to house a tracking tag powered by a Feather M0 with WiFi and a Wing GPS board from Anafruit, along with a reliable 3.7V 1200 mAh LiPo battery. The width...

Case for the Adafruit feather: doubler: https://www.adafruit.com/product/2890 oled: https://www.adafruit.com/product/4650 motor controller: https://www.adafruit.com/product/2927