adafruit gps logger 3d models

Upcycling is an essential part of our future, think ecology!\n\nThe candle holder is designed for use with LED electronic candles and also for makers who want to have fun with NeoPixel rings and Arduino Nano.\n\nThe design accommodates a 9V battery,...

The LCD hole fits a 3.5" Adafruit PiTFT. 02/06/2019: Uploaded a fixed version of the Haribo Text. Realized the X button was too shallow so it may or may not have printed flush with the front of the cover. This should fix that.</p> <p>12/29/18:...

The electronics and firmware are from Dan Royer's Makelangelo project, which includes the software and firmware using the V1 version of Adafruit motor shield, but I used a DK Electronics motor shield instead. I conducted several test trials using...

The Core Can Accommodate LED Strips, As Well As A Microcontroller Like The Adafruit Trinket M0 And A USB Power Pack In The Grip. However, Be Cautious Not To Overload The Prop With Too Many Lights At Once. Update 2: I'm Continuing With The Printing...

This setup uses a PiZero, a lipo battery, an Adafruit Powerboost, and a USB Wifi dongle to do all of the above. My first attempt at housing it was in a Tyvek Wallet, which worked great, but some people asked for a more secure case with easy charging...

And here it is!I printed the body of the portal gun in two parts out of PLA on my Ender 3 V2, as well as the tray that slides in the front.The LED lenses and the plasma tube were printed in clear resin on my Photon mono X.This project needed a lot of...

Using a USB Micro-B Breakout Board from Adafruit was the best option since I only have one official 3DS charger and no adapters. The abundance of cell phone chargers on hand made it easy to find an alternative. Some leftover M2 screws from a...

I purchased the inductive charging system from Adafruit.com, which indicates that the system operates between 9 and 12vdc. However, operating at 12vdc generates excessive heat for most PLA filaments. Using an IR thermometer, I measured temperatures...

The 22 LEDs are 5050 RGB NeoPixels from Adafruit, and a Light Dependent Resistor (LDR) is integrated to measure environmental light levels and control the brightness of the LEDs. A TQFP AtmelMega328 microcontroller powers the system, but make sure...

Now your pi have 5 usb ports :) See [here](https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=246348&p=1678554) ## Parts * Step down converter : [UBEC Buck Converter](https://www.adafruit.com/product/1385) (can be found elsewhere, look for...

### Building Here are the parts I used: * Raspberry Pi 3 * 5" TFT LCD Car-Monitor * Adafruit 2.5W ClassD Mono Amplifier * USB Soundcard * 8 Ohm Speaker * Push Button * Audio On/Off Switch * DC/DC 12V Converter, like the RNM-0512S 1. First, install...

https://learn.adafruit.com/neopixels-on-raspberry-pi/python-usage I believe it would be possible to flash the LEDs in sync with the sound but wanted to keep the setup as simple as possible. Hardware: WS2811 12mm Neopixel equivalents... They...

... The caps can be printed open end up. The electronic components were mounted on Adafruit breadboards and will fit into the included tray. ...I added a 5v 40mm fan to cool the driver chip: at 20V and 1.2A the heat sink remains cool enough to touch.

**Components Needed** * Worm geared motor * Ball bearings (MR83ZZ and MR115ZZ) * M3 hexagon socket countersunk head screws * M3 nuts * Small washers * Frame Ribba 50 cm width (IKEA) * LED-illumination LEDberg 12V (2x) * AlDibond 50 x 50 cm of 3 mm...

The motor I got from Adafruit has 32 steps and a reduction ratio of 1/16.032. At first, it doesn't seem like a good choice for a clock, but technology can give the illusion of a perfect working motor. 32 steps and a ratio of 1/16.032 gives 513.034...

**Antenna Used:** Bingfu Dual Band WiFi 2.4GHz 5GHz 5.8GHz 8dBi RP-SMA Male Antenna 15cm 6 inch U.FL IPX IPEX to RP-SMA Female Pigtail Cable https://www.amazon.com/gp/product/B00VE1XH4A **MicroSD Expansion Board Used: ** Adafruit MicroSD Card...

Combine two or more ULN2803 driven outputs if you need more than 500mA.\r\n\r\n* The 2x3 pin I2C connector is pin compatible with other ft I2C cables (ftDuino, TX).\r\n* MCP23017's specs show the expander should work both with 5V or 3.3V I2C devices;...

I2 TSL2561 and HTU21DF: This enclosure provides provisions for both illuminance and temp+humidity breakout boards from Adafruit, with the temperature/humidity slot featuring hexacomb vents for added style. PIR Dome: The standard Parallax...

This robot utilizes JX-60 (PDI-HV2060MG) servos with a rating of 60kg/cm, paired with custom servo wrappers and brackets, along with an Adafruit 16-channel servo controller module. An esp32 development board receives messages from a serial USB...

###Parts + 1 [KB2040](https://www.adafruit.com/product/5302/ "KB2040") + 30 MX switches + 30 MX keycaps + 30...

It uses Adafruit Pro Trinket 3V instead of Arduino, and there are two other versions with different motors; if you have experience, you can make the adaptations yourself, or I invite you to create your own dibuRobot. I took the idea and here's what's...

You can get the latest versions here: 33cl https://cults3d.com/en/3d-model/home/can-holder-33cl 50cl https://cults3d.com/en/3d-model/home/can-holder-50cl 12oz https://cults3d.com/en/3d-model/game/can-holder-12oz 12oz fl (slim)...

The front cover CameraFrontBottom-fingers.stl file from: http://www.thingiverse.com/thing:403712 Two links, link.stl, from: http://www.thingiverse.com/thing:247590 The fingerclip base, fingerclip.stl, from:http://www.thingiverse.com/thing:403712 The...

... a gear down approach and placing the slip mechanism on the geared-down side may yield better results. In the end, I opted to switch to ["TT" style gearmotors](https://www.adafruit.com/product/3777) and designed a separate adapter for my project.

Each temperature label has its own color, and uses Adafruit's NeoPixel library. Everything is powered by the 5V USB connection, no need for VIN power. The enclosure and arms I designed in 3D CAD are all 3D printed. Feel free to fork an add pull...

In addition to the 3D printed parts, you'll need 4 uSwitches (http://www.amazon.com/Micro-Limit-Switch-Roller-Action/dp/B00H8TIEHW/ref=sr_1_1?s=industrial&ie=UTF8&qid=1459951417&sr=1-1&keywords=micro+switch) 1 M8 bolt of whatever length you want to...

Here are the settings I used: * Baseplate: PLA with a 10% infill and 0.3 mm layer height * Backplate: PLA with a 10% infill and 0.2 mm layer height (printed with the flat side facing down) * Cover: PLA, 0.2 mm (clips onto the backplate and holds...

BEFORE PRINTING, BE AWARE THAT THE PCB IN THIS DESIGN IS CUSTOM AND DIFFERENT FROM ADAFRUIT'S IT IS MADE SPECIFICALLY FOR THE SOFT TACTILE BUTTONS. THE GERBER FILE PROVIDED SHOWCASES ONLY THE BOTTOM COPPER OF THE PCB, BUT YOU CAN USE A PROGRAM CALLED...

I also purchased this 18" TFT cable rather than use the tiny one included with the display: https://www.adafruit.com/product/1730 . This allowed me to mount the Raspberry Pi in the back of the Enclosure. I also believe they sell a 12" and 24 "...

## Parts - [HifiBerry DAC](https://www.hifiberry.com/)* - Power Supply: Meanwell RS-15 - [LCD](https://www.adafruit.com/product/181) -...