adafruit pitft 2.8 touchscreen display for raspberry pi 3d models

I wanted to try using the RPi with an external SSD instead of a SD card so I designed this case to hold the complete setup which also includes a 3.5 inches  touchscreen:touchscreen SSD Drive The idea was to use the SSD as the base of the case, so I...

I wanted to try using the RPi with an external SSD instead of a SD card so I designed this case to hold the complete setup which also includes a 3.5 inches touchscreen: touchscreen: https://www.amazon.com/gp/product/B076M399XX/ SSD Drive :...

This cover safeguards the Raspberry Pi atop the Eleduino Bamboo Display Stand for the Official Raspberry Pi 7 inch Touchscreen, available on Amazon. Print with the back of the cover flat on the bed. The mounting hole corners are reinforced by...

I wanted to try using the RPi with an external SSD instead of a SD card so I designed this case to hold the complete setup which also includes a 3.5 inches  touchscreen:touchscreen SSD Drive The idea was to use the SSD as the base of...

Enclosure for Raspberry Pi Touch Display and some other hardware ;) Hardware i use for my ButtonBox: * Raspberry Pi 3 A+ * Official 7" Raspberry Pi Touch Display * Adafruit I2S Stereo Speaker Bonnet + 3W Speaker * Teensy LC (USB HID Gateway) *...

Enclosure for Raspberry Pi Touch Display and some other hardware ;) Hardware I use for my ButtonBox: * Raspberry Pi 3 A+, available at https://www.raspberrypi.org/products/raspberry-pi-3-model-a-plus/ * Official 7" Raspberry Pi Touch Display, found...

... looking for it. ...Be cautious when attaching the rear casing to the Thin Film Transistor display - there are specific screw holes that need to be aligned carefully and screws should not be tightened too firmly, as this can cause damage to the TFT.

Mounting Bracket for Official 7-Inch Raspberry Pi Touchscreen Display on Rigidbot Frame. ...Two Identical Prints Required, along with Four M3 x 8mm Screws for Secure Installation.

Here's a simple mount or brace designed specifically for attaching a Pi Zero to the back of Adafruit's 3.5" TFT display. As you can see in the images, this design utilizes M2.5 screws to secure the screen itself, while slightly larger screws are...

So I modified the display box file and added this side mount for the pi zero. No support needed.Ideally one should use the w version without the GPIO pin soldered. It should be also possible to change the orientation and moun the wh version, although...

This is a minimalist stand for the Raspberry Pi 7" Touch Display. You need M3*8 screws to attach the stand to the display. The model includes only one stand, so you'll need to print two. I used PLA with 20% infill. You should be able to use...

For comprehensive assembly instructions with pictures, visit http://www.built-to-spec.com/blog/raspberry-pi-and-adafruit-lcd-enclosure. The design is by RoboLemur. ...The cutting guide includes black lines to cut and red lines to etch; files are divided...

This is a simple TV bracket designed for the standard retail version of the ISS-Above which utilizes the Adafruit Clear Case. The case sits on the bracket, with HDMI and power cables naturally falling behind the vertical base. I've discovered that 3M...

Support board for iC880A and Raspberry Pi 2

The Raspberry Pi 4 (3 should also fit) mounts to the official 7 inch touchscreen display. The display mounts to the mount. ... Test prints were done in PLA, but I would use PETG or ABS for a final print, as it will be more suited to the high...

Check out this awesome project that combines the Raspberry Pi Foundation's 7" touchscreen display with the power of a Pi 2 or 3, transforming it into a fully functional tablet complete with a built-in stand. ...The case provides ample space for you to...

The current design requires the following screw and heat insert: - For Raspberry PI: M2.5 heat insert, 4x - For Raspberry PI: M2.5 standoff 5mm, 4x - For Raspberry PI: M2.5 screw, around 5mm, 4x - For holding display: M3 screw, 8 mm, 3x - For cover:...

The current design requires the following screw and heat insert: - For Raspberry PI: M2.5 heat insert, 4x - For Raspberry PI: M2.5 standoff 5mm, 4x - For Raspberry PI: M2.5 screw, around 5mm, 4x - For holding display: M3 screw, 8 mm, 3x - For cover:...

This is a case for Raspberry Pi 4 with 3.5 inch TFT/LCD Display. It is a tight fit and may require some wriggling to fit the PI in. ...This is a very simple and a sleek case.

To use 3 mm screws you need to enlarge the raspberry holes with a bit COMPATIBLE WITH: Raspberry 1 Raspberry 2 Raspberry 3 PRINTER SETTING Extrusion Width:0,40 mm Layer Height: 0,20 mm Top/Button Layers: 4 Outline perimeter: 2 Infill: 20 % Support:...

This sleek enclosure provides a perfect home for your Raspberry Pi, complete with an Adafruit LCD Pi plate board that's installed effortlessly and efficiently. Get your kit now at...

This is a custom enclosure I designed specifically for the original Raspberry Pi LCD display (https://www.raspberrypi.org/products/raspberry-pi-touch-display/). The housing comes in a sealed configuration and an open version with a spacious slot...

Raspberry Pi 7" Display stand

LapTop frame for Raspberry Pi 400 (Waveshare 7inch display version) This is a frame kit for converting your Raspberry Pi 400 with Waveshare 7inch Display [SKU 18068] to a laptop (or portable?) PC without any hardware-modification. Unfortunately, I...

Protective screen cover for the official Raspberry Pi 7" display.

This design is tailored specifically for the Adafruit 1.2" 4-Digit 14-Segment Display with I2C Backpack, making it a seamless fit for the 8020 Series 10 extrusion system.

Assemble the LCD and Raspberry Pi according to the classic method; inverting the board will not work for a low-profile design. 3. Place .75 felt cubes onto the marked indentations on the inside of the backer-board. 4. Insert the assembled...

I designed a stand for Raspberry Pi display (touchscreen). It holds the assembled pi and display at a 22° tilt, plus features a raised front bezel that keeps the screen away from tables when turned over to work or connect with the pi mounted in back....

I designed this simple case to hold an LCD model 2004 (20x4) with a Raspberry Pi Zero that requires no screws or glue. The case itself has rounded top corners as well as the corners of the LCD window. The sides have a wood grain texture due to the...