add laser to ender 3 3d models

I have box I use to keep filaments and with a bowden tube exiting it and I wanted the bowden tube to go as close as possible to the extruder so I designed this adapter, you'll need a bowden tube mount 10mm & an M10 nut and optionally an M2 screw and...

The two coarse thread screws are reused to mount the pcb to the adapter, optional.Designed to move the y axis limit switch from proprietary plastic mounts to the 20xx aluminum extrusion. ...T-nut to channel mount allows fine adjustment of switch...

I tried to reuse parts without modifying them, however, I did have to shorten the motor output shaft by 0.25" to fit, so check for interference. Since the extruder stepper is longer than on a standard Afterburner, I also included the cable cover...

I tried to reuse parts without modifying them, however, I did have to shorten the motor output shaft by 0.25" (~5mm) to fit, so check for interference. Since the extruder stepper is longer than on a standard Afterburner, I also included the cable...

... M3 inserts but you can just thread straight into the plastic for this light application. It's very important that you try to keep the PSU cover all metal, for safety reasons. ...Try to use a solution like this instead of printing a plastic cover.

I used heated M3 inserts but you can just thread straight into the plastic for this light application.It's very important that you try to keep the PSU cover all metal, for safety reasons. ...Try to use a solution like this instead of printing a plastic...

It fits perfectly flush when I use the spacers to blow air inwards, but it can also be reversed to pull air out of the power supply unit, eliminating the need for those spacers altogether. The spacers are designed specifically for the original...

I craft a retro-fitted smartphone dashboard using an elderly mobile device as the primary interface to manage and operate OctoPrint.

It's a hardstop that mounts where the limit switches go to use sensorless homing. ...It's a copy of the 1923 style switch assembly.

I implement these safeguards to shield a critical component and sever the motor's connection when it fails, thus preventing damage to the drive IC of the motor. I incorporate ideas from fellow designers to enhance my own concepts. Below are links to...

This remix reworks https://www.thingiverse.com/thing:3386628 to enable use of the dual gear extruder on a Creality CR-10 in direct drive setup. ...To make this work, you'll need two m3x30mm screws and one m3x25mm screw for the tension release arm.

Personally I prefer a clean part without any logo/arrows/emblems etc. ...I remixed this design to have none of those like in the original. Print this with front facing downwards to reduce necessary supports and cut down about an hour of printing time.

Due to the low availability of spare parts for CR6 i decided to make myself an adapter for hotend that i can mount hotend from creality cr 10. I have never done such things so process was very long and the result is awful, but it works! Works really...

This adapter can be used to connect two stock creality 4024 blower to a 40mm opening. They are held in place by M2 screws, but you could also print pins in the fitting size. I have also found that the 1.75mm filament makes a good temporary fixure....

this is my first ever model i have created with tinkercad so this is a WIP i wanted to make a nozzle box that will sit on the top so i created this

I liked this mount, but I switched from the Logitech 9000 (which doesn't focus at close distances) to a manually-focused Arducam. ... A M3-.50 nut is required.

No more struggling to feed filament into the extruder thru the runout sensor. Such a little block, let it block out the frustration. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/8kPVvzndK9G

No more struggling to feed filament into the extruder thru the runout sensor. Such a little block, let it block out the frustration. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/8kPVvzndK9G

Description: The color of the lamp shows you the status as follows: -Fade yellow: booting/connecting -Rainbow cycle: Printer is ready -False white light: blue to red -Printer is heating the bed, showing every 5°C from 30-60°C -Blue to green: Printer...

I use this proteccions to protect some kind of pull and disconnect the motor where in on, and if it happens, the drive IC of the motor burns. I use some ideas of the rest of the designers to improve my ideas. I leave here the link where I collect...

This is a remix of : https://www.thingiverse.com/thing:3468035 and https://www.thingiverse.com/thing:3143196 It fits nicely below the printer when used with dumper feet: https://www.thingiverse.com/thing:3020865 Adapter I used for this:...

... ... I use PLA+ filament at a 0.164mm layer height for the nozzles, 0.2mm for the bracket. My print temp is 215°C and a bedtemp of 60°C. I purchased this kit from Amazon. I believe it to be a good value for how well this direct drive hotend works.

Make adjustments online at https://www.tinkercad.com/things/fSilOJZSfOv Access the original post, unchanged and uneditable, here: https://www.thingiverse.com/thing:3021807 Yes, same project, but now you can edit it using the provided link to...

I have found a great ps3 eye holder but the problem was that it is just standing, so i just measured the bed height and make to that (7mm in my case). ...I hope it is okey that i used this model, I have no idea how it works here, and if someone have a...

Bailey\r\n\r\nBe sure to check out my YouTube channel: I'm new to the game, so don't judge me!\r\nhttps://www.youtube.com/channel/UCjAuDpiw1tD_dRderr9KXRg?view_as=subscriber\r\n\r\nMy Tinkercad creations can be found...

It boasts faster print times, identical performance, and minimal space requirements compared to mounts like Petsfang, Bullseye, and BantaMount. Some compatible duct designs include: https://www.thingiverse.com/thing:2912394...

Add the Phrozen Transform perforated buildplate to Formware (from v1.0.3.0 onwards) In settings, go to Machines -> Phrozen Transform Select the Build Platform tab In the Build Platform 3D file box, click the pencil icon Select the downloaded STL...

Simple labels for Christmas, just download the files and pass them to your favorite design software (Fusion 360, among others ...) to add the name, logo or whatever you want on the label.

This a new mount design for the Creality Laser Control Box Mount For Ender-3 S1 Series.Watch the video for this new type: https://youtu.be/6Dc4j1YakMQWatch the video for types 1 and 2: https://www.youtube.com/watch?v=CNPbfqxWiTIDownload the files for...

... half into two keychains for a couple, or best friends. Or one keychain that you can print as is or add text onto. I cover how to make these on my YouTube channel ( JesseDoesTech) Make sure to tell me in the comments that you are from thingiverse!