add laser to ender 3 3d models
2531440 3d models found related to add laser to ender 3.prusaprinters
Loved this design from eric-anastas and only read good things about it here and on other groups. Decided to give it a remix as I have a Creality laser module I use for engraving so fired up 123D Design and did a very simple and basic add on to the...
thingiverse
Decided to give it a remix as I have a Creality laser module I use for engraving so fired up 123D Design and did a very simple and basic add on to the one side . ... I hope iot is of benefit to someone else and if you like this remix then Please do go...
cults3d
Decided to give it a remix as I have a Creality laser module I use for engraving so fired up 123D Design and did a very simple and basic add on to the one side . ... I hope iot is of benefit to someone else and if you like this remix then Please do go...
thingiverse
Enabels you to attach a Lasermodul which can be bought from China to the Ender 3 (Pro). Just search for FB03 Laser in the commonly known websites. ...This thing currently only describes the mechanical side.
thingiverse
- Micros SD to SD Card Reader Holder This holder attaches with a screw and nut to the vertical filament bracket. It can be used to hold a micro SD to SD adapter when not in use (e.g.,...
thingiverse
Has anyone else noticed that LED strrip lighting fits neatly into the roler channels on the extrusion on the Ender 3? I looked at so many light bars and different scenarios on offer and always shy'd away because a 2 hour print and trailing wires...
thingiverse
power supply casing with switch and USB port integration. ... https://www.ebay.co.uk/itm/314520945840 this is the USB inputs i have used for this project.
thingiverse
Support to hold the ender-3 laser and remove it easily. https://youtu.be/1oyUh8zMWbE Try to first put the lower part of the piece under the extruder block. And after, adjust the top of the piece to hear a "clic". I've also installed a "rapid...
thingiverse
External diameter of the laser lens adjustment ring: 16.25mm Internal diameter of the cap (design): 16.70mm Internal diameter of the cap (measured after printing): 16.40mm To be scaled according to your printer's tolerance. ... Printing: Print with...
thingiverse
My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x short...
cults3d
My Ender 3 laser kit came with a splitter cable but I couldn’t see the point of it. I’ve repurposed it into this switch to change between fan and laser. ... Houses a on/off/on DPDT switch 28mm x 21.5mm Printed in PLA, needs 2 x M5 T-nuts and 2 x short...
thingiverse
Laser Mount for the Ender 3 that makes it so you can keep your Laser and BLTouch mounted and print as you normally would using the stock hotend shroud.
thingiverse
barcket for ender 3 without modifications please if u make it post it :P
thingiverse
### Filament spool add-on for __Creality Ender 3 Pro__ ### Printed & Tested on * [Creality ST-PLA 1kg Spool](https://creality.com/creality3d-st-pla-filament-p00255p1.html) * [Creality Ender 3...
thingiverse
Use it if you have / want to add 1. Ender 3 V2 Printer 2. BlTouch 3. Direct drive plate from Amazo n ( Link below ) 4. Noctua fans for cooling. I tried many builds but then I had to make my own to fit all my needs I bought the direct drive plate...
thingiverse
Add-on for Pickle_Rick_1's tool holder. ...I needed a place to store my pliers and calipers. ...This fits the 50mm wide power supply boxes.
cults3d
Here are some links related with getting Octoprint on OrangePi Zero and fix it on Ender3: - My mod to stick orange PI zer on the Ender 3 frame (https://www.thingiverse.com/thing:3476249) - Octoprint on Orange PI zero Non-affiliate links: - LÖRBY -...
thingiverse
The bolt I used that holds the sensor in place is a tight fit (it looked like it wasn't going to fit) but with a tap of the hammer it goes in perfectly. HINT ==== Have the BL touch with the logo facing inwards, so the internal PCB is furthest...
thingiverse
Laser Stick to control the laser focus in more safety way. I Use and print it on my Ender 3 V2. ... Resolution print of 0.2
thingiverse
This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...
thingiverse
This holds the standard 500mw laser engraver on the Ender 3. It's compatible with BL touch and provides a bit of extra support and stability for mounting the laser. The laser still uses the magnets for attaching to the fan housing, but this mount...
cults3d
This is a holder for the 0.5w laser module used with Ender 3. My laser module was constantly moving around when it was atached to the printing head only by the magnets because the cable is too stiff. With this, the module stays in position. ... The...
thingiverse
This holder is designed to replace the hotend on the Ender 3 to hold the laser engraver D-B500F instead, which can be purchased here: https://www.creality3dofficial.com/products/creality-blue-violet-light?sca_ref=10788.CFDqhuwn3C The difficulty in...
grabcad
I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering
thingiverse
I was tired of knocking my laser head off on my ender 3 so here is a mount that works with a go pro tightener. This can be changed out for any bolt of your choice. ...Happy printing/lasering
thingiverse
You will need to print with supports, the current design suits standard Ender 3 V2 and also has a cutout for the mounting screw if you have a fang. (refer to .stl - photo shows V1 with smaller cutout) To use this simply lift the Z Axis to 120mm,...
thingiverse
I got tired of cleaning tape residue off my print bed after using the laser engraver mounted on my Ender 3 Pro. So I designed this handy peg tray system to hold things in place for laser work on top of the print bed. The tray is split in 4 to be...
thingiverse
It seems there is no single mount for lasers which will directly attach to the Ender 3 / Ender 5 hotend plate. hm... so we need one... and here it is! Just screw the bracket on your laser head, unscrew your hotend and fan housing, screw the lase on...
thingiverse
I made this to mount the official Creality laser cutter/engraver to the front side of the print head. It should work with any 33mm square laser head. This blocks the fan, so you don't want to leave the laser in while doing any 3D printing. The hole...