adimlab 3d

The ADIMLab gantry can be upgraded with a pillow block bearing, allowing for quieter operation and preventing z-axis rods from moving up or down. By replacing lead screws with 2mm pitch lead screws, users can ensure compatibility with 500mm screws...

This reconfigures the AdimLab Gantry printer to be a single unit instead of having a separate control box. This configuration turns the printer sideways allowing better clearance when backing the printer against a wall. (the bed goes side to side...

9/14/2019 UPDATE: Version 3 of this model has been updated, featuring one version with an Adimlab logo and another without. As a result of the pulley's weakness, its design was thickened for added strength. ...Printing the pulley in PETG or ABS is...

This reconfigures the AdimLab Gantry printer to be a single unit instead of having a separate control box. This configuration turns the printer sideways allowing better clearance when backing the printer against a wall. (the bed goes side to side...

Allows you to use a pillow block bearing with the ADIMLab gantry, making your z-axis rods quieter and preventing them from moving up and down. I replaced my lead screws with 2mm pitch lead screws and found that the 500mm screws I ordered were...

Bondtech_fan_duct - uses the stock ADIMLab hotend fan as a print cooling fan. Plug into the PWM fan socket, and plug the existing LED into the LED socket. Additional 3mm screws are required to mount the fan and fan duct. (Updated 03-30-2019) ...

... https://www.thingiverse.com/thing:3050607 ). Printed front side down with PLA. Supports needed. Check out my other designs in HCMaker7 collection for a full set https://www.thingiverse.com/streloch/collections/hcmaker Category: 3D Printer Parts

... </strong> <div><p>Cubic 35-50 Percent</p></div> <p><strong>Notes:</strong></p> <p>Print as orientated with support. I used tree supports and they worked very well. For strength, I printed with 4 walls. Category: 3D Printer Parts

... ADIMlabs i3 printer. ...The bottom edge is cutoff of the remixed "40mm Fan Clip-On Guard/Grill" thing so it will fit on the ADIMlab printer. It just slides on and yakulis did a great job designing this fan grill cover. ... Category: 3D Printer Parts

... ADIMlabs i3 printer. ...The bottom edge is cutoff of the remixed "40mm Fan Clip-On Guard/Grill" thing so it will fit on the ADIMlab printer. It just slides on and yakulis did a great job designing this fan grill cover. ... Category: 3D Printer Parts

I loved Spirazo's 608zz Spool holder, but with a full spool, it was extremely tight for the filament detector, so I elevated it to prevent any bumping. ...Every other component can be found at https://www.thingiverse.com/thing:3410082 .

This is a new version of the Adimlab Gantry-S adjustable Z-Stop with gears for the adjustment. Please see https://www.thingiverse.com/thing:4240240 for installation instructions. ... Category: 3D Printer Parts

The rest of the parts and instructions can be found at the following link for the Adimlab Printer here: https://www.thingiverse.com/thing:4314318 UPDATE: 3/26/2021 Increased the size of the holes in the air duct to allow an M3 hexhead screw to go...

The rest of the parts and instructions can be found at the following link for the Adimlab Printer here: https://www.thingiverse.com/thing:4314318 UPDATE: 3/26/2021 Increased the size of the holes in the air duct to allow an M3 hexhead screw to go...

I've taken the brilliant design from GWhoop and remixed it to make it even stronger, just what I needed for my 3D printing adventures with my adimlab printer! The original design works flawlessly, and I'm impressed by its quality. ...If you're looking...

This is a Y stepper bracket for a 2nd damper that can be added along with my Adimlab Y stepper mount https://www.thingiverse.com/thing:3127999. This thing should also work with the original Adimlab bracket. Either way its function is to support the Y...

ADIMLAB GANTRY PRO Z-RAIL CONVERSION Warning: This modification uses MGN9 rails and not the usual MGN12.

since i could not find the STL for the alignment tool that came with my adimlab gantry pro, I made this in tinkercad

Designed specifically to fit the Original Gantry Adimlab, this setup demands a dual fan modification and an additional hotend cooling shroud for optimal performance.

Tinkercad link: https://www.tinkercad.com/things/4TySCePNNE5 Print Settings Printer: Adimlab Gantry Rafts: No Supports: Yes Resolution: 0.24 Infill: 10 Filament: MG Chemicals PETG Black Notes: For the slotted version, use supports everywhere (not...

Tinkercad link: https://www.tinkercad.com/things/4TySCePNNE5 Print Settings Printer: Adimlab Gantry Rafts: No Supports: Yes Resolution: 0.24 Infill: 10 Filament: MG Chemicals PETG Black Notes: For the slotted version, use supports everywhere (not...

... 40mm fan grill cover for the ADIMlabs i3 printer. ... The bottom edge is cutoff of the remixed "40mm Fan Clip-On Guard/Grill" thing so it will fit on the ADIMlab printer. ... It just slides on and yakulis did a great job designing this fan grill cover.

......The bottom edge of the design has been modified from the original "40mm Fan Clip-On Guard/Grill" to ensure a perfect fit on the ADIMlab printer. ...Simply slide it on and you'll appreciate yakulis's exceptional work in designing this fan grill cover.

... the LED to be more visible. This cover does not work with the Y Axis Limit Switch. Fully compatible with the ADIMLab X-Axis Pulley Cover I show this cover (and other covers) in a YouTube video: https://youtu.be/JcyTnS-7tlk Category: 3D Printer Parts

This is a remix of "ADIMLab Z-Axis End Stop Adjustment" by Rabbit1210 to adapt it for the Adimlab Gantry-S 3D printer. Remove the factory bracket and the z stop from the bracket. For the knob, you will need an M3 x 40 screw, one M3 nut, one washer,...

... paired with a Customized Cooler, tailored specifically for its sleek and sturdy design. ...This bespoke cooling system was crafted to perfectly complement the Adimlab Gantry, providing a seamless integration that maximizes performance and efficiency.

This is an advanced version of the Adimlab Gantry-S adjustable Z-stop, featuring gears that allow for precise adjustment. ...For detailed installation guidance, visit https://www.thingiverse.com/thing:4240240.

I've accumulated various components for the Adimlab i3 Gantry printer over time, including a custom cover for the extruder that incorporates an integrated mount for an auto leveling sensor.

This is an enhanced edition of the excellent "ADIMLab Control Box Front Panel" by FerretWorx." It includes an SD card slot; features a flat front design instead of tapering off at a point and showcases a more prominent logo, along with some...

This is a Y stepper bracket designed for a second damper that can be easily added along with my Adimlab Y stepper mount available on Thingiverse at https://www.thingiverse.com/thing:3127999. This design also works seamlessly with the original Adimlab...