adjustable ir mount 3d models
435527 3d models found related to adjustable ir mount.thingiverse
This is an adjustable mount for David Crocker's mini differential IR sensor. It is attached to the front half of the clamp that is commonly used to hold an E3D V6. This makes it very easy to install without replacing other parts. I started with...
thingiverse
Adapted from article here: http://hydraraptor.blogspot.com/2011/02/polyholes.html Edited the OpenSCAD file from MarkBenson's thing to allow more straightforward adjustment of dimensions. The original was for a 30mm fan and I wanted to attach the...
thingiverse
remixed this thingie for 40mm mount : https://www.thingiverse.com/thing:1581152 Added thermal shield (sort of. hope it works :) ) This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/hibKrA0dg0w
thingiverse
I wanted an adjustable camera mount for a Raspberry Pi Camera with IR leds. ... Requires: 1x M3x12 bolt to secure the mount to the Ender 3 2x M3x20 bolts 2x M3 nuts 2x M2x5 bolts for attaching the camera module to the printed mount 2x M2 nuts Print out...
thingiverse
Addition for design https://www.thingiverse.com/thing:4337578 The original mount is -15,5 degrees. For the raspberry Pi cam with the 130 degree view angle the distance to the heated bed is to big. ... So I made a 0,0 degree and a 15.0 degree version.
thingiverse
Remix to make the Pi IR camera work on an Eryone Thinker S (better angled arm with two screw holes), and with the Pi HDMI adapter on the back as an optional second part. ... Requirements - [from original...
thingiverse
I designed this little adjustable adapter plate to mount my DC42 Mini height sensor board to my E3D X-axis Carriage where the BLTouch would normally be installed. This works out great as the large hole allows a screwdriver to be inserted to raise...
thingiverse
OpenScad recreation of http://www.thingiverse.com/thing:950478 that adds adjustable mount holes and is a bit thicker for strength.
thingiverse
This is made for ATN 410 Spartan but will work for every nvrs that have an external weaver mount for ir illumination. ...This one i use with a 16x60mm 850 nm focusable laser on 160mw and that one is much moore efficiant then the stock ir that comes with...
thingiverse
... just print it as it is, punch out the original pin which connects the oriignal foot with the lamps head and replace the foot with the mount. Screw the mount to any camera tripod and you have a fully adjustable IR lamp to cure your very own backpain!
thingiverse
A fitting for mounting an IR sensor to a Titan Aero. ... The updated mount is for the Duet3D IR mount.
thingiverse
... Robo3D Forums) it slots onto either the front or the back of the carriage. adjustable up and down to give you maximum accuracy prints quickly, also there is only one screw that holds the PCB mount to the clip mount to allow it to be adjustable.
thingiverse
Simple mount for IR sensor distance. ...Two versions: - normal - 90° curved
thingiverse
To mount the Harmony IR Repeater an the Wall (eg. ...behind the TV)
thingiverse
Mod of CDRSKULL's IR holder. ...This mod allows for adjustable IR sensor height and accommodates larger screw heads where attached to printer head.
thingiverse
Stereo IR 170 is kinda picky that it will only work with the cable side sticking up, that's why there is a cable feed built into the mount. Printing: I printed this on my Ender 3 pro, with PLA+, using Cura, and at low quality. ...Currently no...
thingiverse
Mount for TSSP58038 IR Detector Mounts under slot for slot car track timing and lap counting Uses 2 #6 x 1/2" wood screws Mount detector with a small piece of double-sided foam tape (servo tape)
thingiverse
On mount is for a 5mm IR diod (Transmitter) (will work for other diods aswell) The mount is ment to fit into a hole of 8mm, the diod should fitt snug, but i podded the mounts with epoxy. The other mount is for a IR reciver, this will requere the...
thingiverse
This is a quick IR mount I made for the TCRT5000 IR line following sensors. I am currently using it with an Arduino robot for following a maze. The lines being followed are 3/8" wide. Feel free to remix this mount and change the distance between...
thingiverse
I am completely new to 3D printing and this is my first creation from scratch. ... I made this so I could mount an IR remote transmitter in front of my A/V equipment. ...
youmagine
... of something, instead of on the outside.I've provided a variety of vector formats. One of them should work with your laser cutter / software.There's a blog post with more info: http://rasterweb.net/raster/2014/11/19/ir-proximity-sensor-mount/
thingiverse
This is my solution to hang the IR-Blaster from zemismart to cover all room IR signals, my IR Bridge is a round one, mas diameter is 75 mm adn 35 mm thicknes.
thingiverse
... cutter / software. There's a blog post with more info: http://rasterweb.net/raster/2014/11/19/ir-proximity-sensor-mount/ Instructions Use a laser cutter and 3mm (or 1/4") material. Wood or acrylic should work. ...You'll need to glue it together.
thingiverse
Internal Chassis BCIT - Undersea Laboratory This is the Front IR Ring Mount for the BCIT Undersea Laboratory. It provides the system with an array of 12 controllable infrared LEDs for night vision, as well as 4 mounts that fit any of our external...
thingiverse
I used this: https://www.thingiverse.com/thing:2836769 for the base, bracket and arm, but I have a camera with IR, and this design did not fit it, therefore I put together other parts and modified them in order to make a case for my camera. ...On the...
thingiverse
This design is a push-in sensor mount for the Sharp GP2Y0D805Z0F on a pololu carrier. ...Mount it everywhere you want with hotglue or screws.