adjusting z axis ender 3 3d models

When working on the z axis you can hold the heatbed inplace with the hook on the frame. Use 2 hooks on the left and right side of the bed. Update made the hook little bit longer to have more support. ...(85mm version) Also added a support ring if...

EN: This clip prevents the print bed from moving down (by its own weight) when the motors are switched off after the printing process (Z axis). The clips are easy to put on and allow a movement in Z-direction if the part to be printed is very high...

Ender-3 Z-rail cover preventing filament contamination

This is a cover for Ender-3 Z-end stop.

Since the Z-axis motor is not aligned with the z-axis carriage i had to create a spacer between the motor and the printer. ...This Spacer allows you to use the provided screws and no drill is needeed.</p> <h3> Print Settings</h3> <p><strong>Printer...

The EVA carriage (https://main.eva-3d.page/) is great on the ender 5, except the rear mounted blower eats into y travel by contacting the z-rods.  This mod relocates the rod support down 20mm to clear the carriage and not hit the bed mount. ... Some...

Ender 3 Y-Axis Cover Update 1.2 Release: Smoothened Corners Unveiled The latest upgrade for the Ender 3's Y-axis cover has finally arrived, boasting a major improvement - corner fillets. ...This new feature brings an enhanced aesthetic to the cover,...

Adapter to install a thrust ball bearing over the Z axis step motor and finally relief the bed weight from its radial ball bearings. - Must replace the four original screws by four M3x10mm. - Recommended to glue the spacer under the adapter...

This is a mounting block to attach the 8mm Z-axis spindle of the Creality Ender 3 Pro to the 2020 profile. ...The required ball bearing is 16mm in diameter and 4-5mm high on the outside.

I built an adapter to lift my Z-axis carriage plate above the Z-axis stepper motor so it clears.

... length of 30mm is necessary. A thrust bearing must be included in the design. A shaft collar is also a crucial component. A spacer, recommended to be at least 0.5mm thick, should be used to adjust Z settings according to your specific setup.

You can also print it vertically with a brim to enhance adhesion on an Ender 3 or Ender 5-sized bed, or diagonally across the bed if preferred. We printed this part at 20% infill with five walls for added structural integrity and durability. The...

The Ender-3 Y-axis shield is simple to print and offers a snug fit. ...To install it, loosen the bolt by a few millimeters, then insert the shield and retighten the bolt.

Always forgetting what direction the X axis moves so I came up with this solution Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Filament: ESUN PLA+ Black Category: 3D Printer Accessories

spacer made for the stepper motor and the aluminum profile, for a correct align between the thread from the z motor and the aluminum profile.

By incorporating this bracket, the ENDER 3's Y-AXIS stiffness should be comparable to that of the Pro Model, which utilizes a 4040 Y Rail instead of the standard 2040 rail. This reinforcement was printed using PTEG material and initially sliced with...

You will need: 1 x Notched Lower Filament Guide 1 x Roller Filament Upper Guide with Z-Axis Stabilizer 2 x 17mm Pin Enlarged Barb 2 x Filament Guide Rollers 3 x 608 Bearings (Purchased, I used:...

... Ender 3v2. ...Did the design using github and the fusion360 cad files. Works well with Ender 3 / Pro / V2 Z axis motor mount https://www.thingiverse.com/thing:4699747 Some hardware wil be required to install. ...spacers 9mm and longer screws 40mm.

I added a second z-screw to my ender 3 and wanted to test the stability/straightness of the z-axis. 245mm Tall x 10mm diameter. I used "vase" settings for single-layer walls. Skirt only bed adhesion for adhesion test as well. ... using 60mm/s print...

Screw Stabilizer for the Ender_5. Prevents the bed from falling after prints. I designed it this way on the bed to print a perfect circular hole for the screw. So, in your slicer, have it stand up on the thinner part. Lower the bed down so there's...

A small spacer can be screwed onto the Ender 5's spacer screw if switching to a thicker glass build plate is desired. To prevent losing this small item, I added a tab to hang it on the screw when not in use. It should be customizable, but...

The screen is moved to the top to clear the front dual Z rods. Here is the final video on the update. https://www.youtube.com/watch?v=K8XcjvKydSA ____________________________________________________________________ This is a remix of the...

Very simple cap for the Ender 3 Z rod. ...Fits Perfect!

Replacement part for ender 3 z-stop switch mount. ...*Bed MUST be leveled again before using*

A comprehensive guide to calibrating the Z-axis on an Ender 3 printer, specifically designed for users new to the process. ...This setup can be securely fastened using M4 screws in conjunction with nuts, or alternatively, utilizing M4 nuts alone for a...

Building on hamkers' impressive arm design, this creation is specifically tailored to fit snugly onto the end of the Ender 3 Y Axis frame without any tools needed for removal. The result is a motionless arm that rivals the original mount's stability....

Decorative cover that hides the QR code on the x-axis cover of the Ender 3 v2. The original sticker is removed and the cover plugs into the screw heads of the original cover. The blank canvas offers a nice way to personalize your printer. You...

Creality Ender 3 Z endstop mount Created in Fusion 360 with measurements from the Z endstop mount on my Ender 3 V2 and wanted to have a spare "just in case"

Creality Ender 3 Z endstop mount Created in Fusion 360 with measurements from the Z endstop mount on my Ender 3 V2 and wanted to have a spare "just in case"

Y-Axis Endstop for Ender 3 with Dampered Motors The extruded feet on the back of this endstop prevent it from slipping over time. This feature is especially useful if you've upgraded your motors to Nema CNC stepper motors, which are slightly longer...