adventure time lumpy space princess 3d models

It's not too hard to put these together with a little time and effort. Hopefully, this is useful to those who are makers and want to save a few bucks on this type of device. If you wanna support my development efforts any donation is appreciated and...

The camera may be plugged into the Pi at this time, but the Pi is not yet ready to connect to the header and touch screen. Solder wires to the +V, Ground, SDA, and SDC contacts of the thermal camera. Connect the Pi as a standalone computer and use...

The mechanism may be a little stiff at first but should loosen up over time. ...A little big of silicon lubricant could also be used on the dovetail joints to make it work more smoothly.</p><figure class="image image_resized" style="width:81.16%;"><img...

The Double D is a compact crossbow pistol which fires two arrows at the same time. It can be pre loaded with the two arrows ready in its chamber and can then be cocked quickly and fired. It has a break-action and is breech loaded. DISCLAIMER: By...

It drastically improves OctoPrint boot time and responsiveness, handles HD webcams, and enables heavy server plugins like automatic print-failure detection. The mount grants unobstructed access to the Pi's USB and SD card ports and completely...

This has made it possible to do 1 mm retractions in under 50 ms (32 mm/s, 2000 mm/s² acceleration), and to use a very low smooth_time of 10 ms with Klipper's Pressure Advance, for accurate extrusion at high speed and acceleration. The gearbox...

Gravity is relatively constant (for the time being), so experiment with tressel heights to obtain the best combination between track slope and track length. The tracks I've assembled run for days without a marble jumping the track.</p><p>11) Connect...

... very center one. &nbsp;This way you can generate gcode for all the outer squares so you can test just one square instead of having to do the entire 3x3 grid each time. ...&nbsp;Simple 1-2 minute print to check your UBL adjustments.</p><p>&nbsp;</p>

&nbsp; Screw from behind.9º - You will end with something like this!10º - Time to pass the Belt across our Tensioner.&nbsp;11º - Now pass the belt into the Bed-Holder Too, &nbsp;as shown in this image. &nbsp;Is easy in this step.&nbsp;<br><br><img...

PETG has a harder time getting the fine lines on blade perfectly smooth.  Use of Supports: Yes - Bed Supports are encouraged if printing the knife on the opposite side of the Night Raid logo. If printed along the spine of the knuckles (not...

The self-supporting bridge to hold the core is raised because it needs that thickness, while the surrounding portions of the gate were kept thinner to reduce print time. The one disappointing issue here is thatthis NOR gate requires manual reset. A...

Apply a thin layer of glue to the outside and inside all around to ensure an airtight seal, or it will leak. Now glue the two parts at the same time to the already assembled part. Having someone else hold the top part can be useful here, but it can...

Snap it out at any time by popping the bottom back first.The pedals should now push down the triggers all the way when fully engaged.Face Button, Dpad Arms, and Bumpers:Print with support (bumpers are okay without)These are designed to fit in the...

The mechanism may be a little stiff at first but should loosen up over time. ...A little bit of silicon lubricant can also be used on the dovetail joints to make it work more smoothly.</p><figure class="image image_resized" style="width:81.4%;"><img...

Solder wires to the magnets Now the LEDs and wires are in place and it is time to attach the magnets that will be used to connect the two pieces and simultaneously conduct the electricity, turning the lamp on. When magnets get too hot they can lose...

Full view Full view Full view Full view Full view GCODE used for Benchy Here's the time lapse of the 3D Benchy print Then I strapped it up by one side… Setting up the test Timelapse strapped up. Checking out the results! I am writing the...

Something like this: https://www.amazon.com/3Dman-Toothless-Aluminum-Timing-Printer/dp/B07RV2T54M/ref=sr_1_4?crid=13F2TAX7G9RHI&keywords=GT2%2Bpulley&qid=1707020243&sprefix=gt2%2Bpulley%2Caps%2C109&sr=8-4&th=1SeeMeCnc's 178mm ball arm set:...

Around the time that we were building the small version of the J2 engine, he mentioned that he would love to have a larger more detailed model of the engine. This started me on a search for a printable model which didn’t exist, although I did find...

However for the X and Z axes you'll need to strip the printer down quite thoroughly so even though not required, it makes sense to do them at the same time. The choice of whether to use socket head cap screws or button head screws is up to you. I...

Then when the other foot comes down the body lifts again but this time precesses counterclockwise - and voila, it walks!All the parts you need (bearings, screws, etc.) are listed in the instructions, including the 104 pennies used for the flywheel...

And when it’s time to cut, just pull on the main tube and you expose the filament right at the head. Hope this makes sense. I just cut my original tube at the head, about 5mm up from the black collar.   Simple, works, a little awkward when loading...

Mine fit fine, but I did cycle it a couple dozen times in the channel before assembling it. <ul> <li>Also verify that the small notch that the spring retainer will lock into (in the door), is free of support material. </li> <li>To assemble the latch,...

The previous design did not account for wear on the blade and failed as a result after a short time. The new design also increases the blade slot size to allow easier insertion into the plunger. The tight version is still available for well tuned...

There are plenty of solid resources out there that describe slicers and how to use them, but this will take time to master.OPTIMIZED BRIDGING: I've been doing some of my own tooning on the ole' Bambu Lab X1C, and wanted to share (and document) my...

Even double the swatches fit into the “Times2” version, which has two boxes side-by-side (so 30 swatches times 2 = 60 swatches).&nbsp;Even more sizes are possible of course using the OpenSCAD source code and customizer!The lid has either no label, or...

The 2 piece model will need supports to print the dovetails properly, split the model apart and print one at a time if needed. Once it is printed remove the supports and test fit them together, glue is not necessary on the joint but better to be safe...

Maybe you should print it alone not to fail the all plate of pales if it unsticks.- Plate 5 (Fishes) : 0.2mm z-height - Color change at 0.80mmThis part must be printed in 2 colorsI use External perimeters first for more precise engravings- Plate 6...

Why when making one is FREE and fun!.With Farmers more and more looking at higher yields from there land it means they are turning to chemicals that has an adverse effect on the surrounding land and creatures.So having a bug hotel will help to...

The camera may be plugged into the Pi at this time, but the Pi is not yet ready to connect to the header and touch screen. Solder wires to the +V, Ground, SDA, and SDC contacts of the thermal camera. Connect the Pi as a standalone computer and use...

Inspired by PIRASP'sminimal MasterSpool I finally found some time to design a MasterSpool for small printers which is quick and easy to assemble and disassemble, e.g. no screws, glue or other stuff.</p><p>In contrast to the inspiration source this...