aio gpu 3d models

Same desing with 23mm distanced spacer addon you can use 20 or 30 degree as your prefer.

Ever get frustrated that your capacitor falls off from extreme flights? Fear no more! This 30x30  mount for a 4 in 1 ESC actually (30.5mm x 30.5mm) holds up to an 11mm wide capacitor securely. ... Safe Flying.

There are other designs out there but sadly they didn't fit correctly, so I made my own! ...It's not very pretty but works perfectly fine with my H100i v2 and ROG Strix B550-F.

Ultra low profile DJI Goggle module mount / case system. Easily fits in the goggle bag with antennas on or easily removed. Designed for the "ANALOG FPV FATSHARK MODULE ADAPTER V2" (got mine from...

This versatile box empowers users to effortlessly install their preferred vtx on a high platform, securely holding two 2200mah 3s lipos while also accommodating voltage monitors for low-voltage alarm functionality. This upgraded version boasts the...

Toyota Tundra Vape Stand for cup holder 2020

Made this on Tinker Cad I got tired of my vapes falling over and over and over and over and over and over and over and over. ...So I made this ting!!!

Optimisation des aimants intégrés à l'intérieur du modèle et pas à l'extérieur. ... Optimization of the magnets for the fan ducts (inside the model and not outside) This is a remix from https://www.thingiverse.com/thing:3359098

Made this for my Ender 3 Pro external electronics case. I printed everything and then realized I hadn't left any access to the USB or SD ports. Other than this, I had to cut the sides of the enclosure in half. I used Prusaslicer to orient them so...

Remix of the design, I removed the plug cavities on the back and added holes for direct wiring. I removed the fan on the top. I removed the Ender logo from the front and added a grill for front to back flow. There are two left side designs, one with...

The parts should be fairly easy to print and put together, I designed both parts to require minimal supports, I've also made a step-by-step tutorial for the ender 3 pro as such with images to assist in assembly. (Process should be very similar across...

Install Instructions Easy way: The Github has an installer you can just run and install. Hard way: Just download the master zip and drop the files into your cura install folder NOT THE APPDATA.The most common install location is C:\Program...

Based off the originally modified Tevo Single hotend mounting plate available at https://cad.onshape.com/documents/6759d1e042f95f01cb435ae2/w/77112970a468088c62473312/e/056040e0856b0da923e4d494, a 75mm blower from Amazon was sourced at...

I really liked Tklus's belt tensioner design but on my laser engraver the acrylic legs/feet were in the way. I saw the design for the legs that i've used as a source but they still use the horrible screw clamp method which damages the belt. ...so i...

The X-Axis Motor End is a comprehensive solution that combines everything you need to get started right out of the box. The Cable Chain Mount provides a secure and stable way to attach your cable, while the Endstop Mount ensures precise control over...

Adding some acents to an earlier upload

I got a tinyhawk cheap, i can not get it to bind, so i wanna put a crazybee board in it that i have here...... so here we are :) https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner...

Hose seperator for water cooled PC, desinged to fit 12mm hoses

This is a remix to add an external antenna to this mount and move the mounting point. Also added a few tabs to the top to protect the camera if the car is rolled. The stock antenna is very fragile. I had to remove the old one. Then cut off the 90...

This section has not been tested yet; I will post my feedback soon. This is an all-in-one support for the Deformation insects 130mm quadcopter frame. It includes: An O.D. 12mm buzzer support A Tx double antenna support (here a FS-ia6b) A Eachine...

simple mount for a betafpv m01 or disconnected z01/2 to nano (14x14) camera mounting dimensions. ...Print in tpu and use m2 screws.

***Uploading tweaked version of the top and base to allow probably too cheap PC reservoir acrylic housing. 6mm thick walls is what Im working with. The first version is about 3mm reservoir walls. In light of acrylic being stupid, uploading a printed...

This project is rapidly taking shape. I have just finished printing all the pieces and will soon start assembling them and taking photos. The design has evolved significantly over time, leading to a wide range of options. Development notes: The...

No supports needed. Print in abs or pla. ... Do use a ziplock to fix the camera mount to base, fix with the same screw of wings.

The innovative Floss Tray by AquaTech is specifically designed to work seamlessly with the highly advanced Innovative Marine NUVO 40 All-In-One aquarium system. This cleverly crafted tool enables effortless cleaning of the water column, ensuring...

Designed up this to prevent sagging on the lower side of the Printer

After looking and trying other mounts, I ended up making my own design as I wanted my 8mm inductive probe as close to the nozzle as I could get it. I wasn't able to find something already made that I was happy with, and I think it turned out pretty...