air assist k40 laser 3d models
126389 3d models found related to air assist k40 laser.cults3d
Air assist air duct and bracket for a K40 laser. ...Using a 12v axial fan.
thingiverse
Air assist air duct and bracket for a K40 laser. ...Using a 12v axial fan.
thingiverse
This is an air assist for the K40 laser cutter that works with a simple radial fan. ... Details about the installation and the post-print processing are described in this video: https://youtu.be/Q-7hgnYkgd8
thingiverse
Adaptor to fit Air assist and laser diode to the head of the K40. Laser diode is sight for 50.8mm. ... Requires: 2x M3 square nuts 2x M3x8mm screws 1/4" BSP press air fitting 5v laser diode
thingiverse
An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...
thingiverse
The was an attempt to design an air assist nozzle for the K40 printer. The nozzle works with the existing laser head and attempts to utilize lamar flow. So far I have had decent success with it but have not tested to see if has increased my cutting...
prusaprinters
An Air Assist Nozzle for the Stock Laser Head on the K40 Laser Cutter. The aim of the project was to design and build a lamar flow laser head to increase the cutting ability of the laser. ...Initial testing has not been started but if you print this...
thingiverse
This is an air assist nozzle fro a standard K40 laser cutter. - It is designed for a focal length of about 51mm from the bottom of the original laser head. - The nozzle extends 45mm below the bottom of the original nozzle. - It uses 8mm (OD)...
thingiverse
K40 laser air assist adaper, with 1/4 push In connector threading, upright and angled version
thingiverse
This is my version of the Air Assist Nozzle for the Chinese Laser Cutter Engraver K40. It work great using common fish tank tubing. ...
thingiverse
Die beiden Teile sind die simple Konstruktion eines air assist für einen K40 Chinalaser. Als Luftzufuhr habe ich einen 8mm (6mm innen) Druckluftschlauch genommen und den durch eine Schleppkette mit 10x10mm gezogen (Amazon). Bei mir steckt ein...
thingiverse
This thing is a custom made air-assist nozzle for the popular K40 laser engraver/cutter. It mounts on the stock head. The STL has a 1/4NPT thread for pressure air quick connect and a side hole for M3 brass threaded insert to secure the assembly onto...
thingiverse
This K40 air assist solution consists of 3 printed parts: (1) Nozzle (creates low volume airflow exiting the laser lens area to prevent smoke or vapor from settling on the lens) (2) Splitter (directs most of the airflow through a blower tube at the...
thingiverse
This air assist helps, not only with the air jet that blows on to the part that is being engraved but also, keeps 2 laser pointers aiming at 1 single place. this helps not only with the place where the laser touches the surface but also with the...
thingiverse
In short I got a fancy air assist head for my laser cutter and it wasn't so great and a bit rattle'y. There are plenty of 3D printed attachments for improving your K40 but not so many you can cut on your own cutter so I made this. It basically takes...
thingiverse
Air Assist Nozzle including fixture for two line lasers. The line lasers look straight downward and build a right angle cross - if properly aligned, the cross is exactly where the CO2-Laser hits the target, no matter how the hight is adjusted. The...
thingiverse
... the way it mounts. ...need a m4 25mm long bolt and nut. and 3v laser diode https://www.ebay.com.au/itm/3-5Volt-Mini-Red-Dot-Laser-Diode-Module-650nm-5mW-6mm-Brass-Body-Copper-Head/263680362989?hash=item3d649309ed:m:m9Ll_TGPE-JmW7rutCtTkQg:rk:1:pf:0
thingiverse
Up for your printing pleasure is yet another air assist for the Chinese laser cutter. I did incorporate a boss for adding a 6 mm pneumatic elbow fitting for macro line. It has a 5mm opening for the air. 2 holes 180 apart to for holding to head, tap...
thingiverse
I tried several air assist nozzles that are out there and they all had interference with a cross beam under the mounting bezel so I could not use them without modifying them. For this one I made the cone area recessed so that interference is gone. I...
cults3d
... solotion that fullfill my needs. ... The model fits on the head laser with 25-27mm and can be screwed to fix. The laser pointer can adjust by rotating to better match same target as CO2 laser burn place. ...Tha laser pointer cannot be larger then 13mm
thingiverse
... that fullfill my needs. ... The model fits on the head laser with 25-27mm and can be screwed to fix. The laser pointer can adjust by rotating to better match same target as CO2 laser burn place. ... Tha laser pointer cannot be larger then 13mm
thingiverse
Laminar Air Assist Nozzle for K40 Laser Cutter Inspired by the same design that I read from Hackaday. ...Forgot the source so I designed my own.
thingiverse
This is an air assist for the K40 laser cutter that works with a simple radial blower fan. ... Remixed from: https://www.thingiverse.com/thing:3017700 changed blower fan screw holes to be only 4mm changed laser head screw hole to be only 3mm and work...
thingiverse
Air Assist with Connector for 8mm Pressured Air Pipe and Holder for Red Dot Laser. Mounting of air assist with M4 screws, mounting of red dot holder with M4 screws. ...Clamping of red dot laser with M3 screw.
thingiverse
K40 Air assist, with DesignSpark Mechanical CAD File. Uses 1/4 inch OD brass tubing although aluminum will work also. It is designed so that the tip is aprox 4mm from the work piece when the focal point is 50mm. I made this because the printed...
thingiverse
... Also reduced the airline hole to cater for a smaller tube. NB!! DON'T CRACK YOUR LENS!! To avoid the risk of cracking I unscrew the lens cap and take the lens off, then sllide the air assist on. ...I then screw the lens and cap back on.