airsoft p90 3d models

Airsoft P90 model i made years ago, some parts are missing, but most of it is modeled.This version is not completly finished,i made finished version for competition, but it got lost and i have only this partialy finished one.Most dimensions except...

Airsoft P90 model i made years ago. Most dimensions except hard to measure ones are in 0,1mm tolerance (measured with analog calipers). This version is not completly finished,i made finished version for competition, but it got lost and i have...

Magazine cap for the ends of airsoft P90 magazines.

Made a back cover for a airsoft P90. I had a friend that bought a used one that didn't have a back battery compartment cover. ...Print settings are 0.3 mm layer height, 10% infill, 2 shells, 230 C and supports enabled.

A new magazine catch I designed to fix the broken one on my airsoft P90. May work for real steel ones, not tested. UPDATE 8th Dec 2013: Added new files, original one was too tall to fit in the body of the P90 itself. New file also has wider grips. ...

Made a extended back battery cover for a airsoft P90. I made a regular cover and remembered seeing someone talking about a extended cover for extra battery space on the airsoft group. ...Print settings are 0.3 mm layer height, 10% infill, 2 shells, 230...

Wandhalter für Airsoft Gewehre wie die Cyma CM.060, Begadi PD9, Krytac FN P90, Novritsch SSR90. Achtung Ihr braucht zum anschrauben einen Langen Bit oder zwei schmale Bithalter die ineinander gesteckt werden müssen. Einmal Mündung nach rechts und...

I designed this because I couldn't find any decent P90 mag holders for plate carriers

Handstop for P90 The design of https://www.thingiverse.com/ostrovak is used as a reference https://www.thingiverse.com/thing:3396337

This is a Front Handguard design ONLY for airsoft use so that you can remove the upper receiver freely with it on. Uses M-lok accessory or rails and comes in two versions. The barrel washer is there for those who do not have the threaded washer thing...

... install a microswitch directly behind my p90 trigger. ...Some parts needed to be filed down or cut away for it to fit correctly. I included the .obj if anyone wants to improve it. This is for the CYMA P90 idk if other brands have different internals.

... blender. ...All my slings one or two point slings did not work with the P90, so i made this adapter. It's mainly for one point slings but might work with two point slings. ...Print with no raft or supports, might require some cutting to get it to work.

This is on my King Arms P90 but should also fit the new Krytac P90. To fit it replace the standard M5 side rail bolts with longer M5 countersunk bolts. I used M5x16. ... I've also included a version with 4mm holes in the front to bolt on a lens...

The retaining ring on my p90 barrel broke so i designed this to replace the part. ...It seems to be a tight fit, but that was a good thing for me.

Simple adapter to install a micro switch on P90. You will only need to replace this one part Print all three, only difference is the length of the trigger pull. You will need mosfet (otherwise you will only have a full auto). I used burst wizard...

I designed this a while ago when my p90 trigger broke. I have recently printed one out and it appears to be working flawlessly. I did have to do some smoothing on the bar part in the back, but other than that it seems fine. ...I suggest using abs so...

This is my adapter to convert an airsoft P90 to use standard M4 magazines. This is still currently a work in progress. You will require 3 M3 countersunk screws (designed to take standard airsoft gearbox countersink screws). Two of these are for...

Removing and placing mags in is similar to the motions of reloading a mag into the p90/ps90 Use of stronger springs will make removing the mags harder but have better retention. You can rotate the back part for high or low positions. The completed...

Hopap tuning wheel for P90 2 variants with different inner diameters Part of a larger project https://www.thingiverse.com/thing:5171170

Hopap tuning wheel for P90 2 variants with different inner diameters Part of a larger project https://www.thingiverse.com/thing:5171170

This is a picantinny rail to fit on the sides of the p90, designed for a P90 Tokyo Marui. The rail is attached with the original screws to the sides. Print with support and 0.1 layer height for optimum quality, you may need to drill the little hole...

i am using a CYMA p90 but this is modelled off a standard p90 mid cap so should fit any. main body print time is around 13 hours. everything is 3d printed including spring for mag release, will need to be glued in place. also a pin is needed for...

Old project released https://youtu.be/MCwTS6F9na8

The WE P90 is a fun airsoft gun. One disappointment for me was the light plastic tri-rail upper. This adapter lets you run a metal AEG spec upper (in this case a Classic Army upper which happens to be on sale right now for $35 US...

Airsoft FN-P90 red dot to Picatinny conversion kit. note1: you will need to drill a hole in the adapters for whatever size screw that you want to use. note2: the Adapters are cross compatible with Aim Sports Uncut Picatinny Rail Blanks if you want to...

Ramp to help with p90 hi-cap magazines not feeding properly and jamming. Take the magazine apart and stick beside the first feeding wheel to stop bb's feeding the wrong way onto the feeder wheel and fighting against the box spring. ... Didnt take...

ARM for P90 hop-up When printing on an FMD printer, it is advisable to print 2 or 3 hands at the same time, as there may be overheating and the model may deform or tear off the table Part of a larger project https://www.thingiverse.com/thing:5171170

ARM for P90 hop-up When printing on an FMD printer, it is advisable to print 2 or 3 hands at the same time, as there may be overheating and the model may deform or tear off the table Part of a larger project https://www.thingiverse.com/thing:5171170

Needed a suppressor to hide an extended barrel on my Airsoft P90, print the part and at the back you'll notice a slot to drop a nut into, screw fits in from the bottom allowing this to be locked into place. If anyone has any specific suppressors...

Customized version of https://www.thingiverse.com/thing:1258690 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1258690