airtight container for 3d filament

Here in the Netherlands, the humidity is around 45-50% in house and therefore I decided to store all my filament in airtight containers together with silica gel The filament used for printing is also stored in the airtight box and is fed to the...

Parts for adapting an airtight storage container* for holding filament while printing. It only works with narrower spools, like the ones used by NinjaFlex, Filamentum, Colorfabb, or Up!. I purchased it hoping it would work with the larger spools...

Parts for adapting an [airtight storage container*](http://amzn.to/2hb9LuJ) for holding filament while printing. It only works with narrower spools, like the ones used by NinjaFlex, Filamentum, Colorfabb, or Up!. I purchased it hoping it would work...

I searched a long time for an storage box where my filament is save from air humidity. My setup is that my printer stands at the ground in a corner of a room and i build a wooden box around it. I have a 3 in 1 Nozzle from Geeetech, so i always have...

Stand designed to work with "Snapware Airtight 40 Cup Rectangular Food Storage Container" but it will work with any airtight container or box. Uses 608 bearings for the axle. Super easy to pull filament from. ...Works with an airtight box and basic...

... https://www.thingiverse.com/thing:4930292 Thanks to Augustusbot for posting the link to the containers originally on this site. I've searched for a long time and could never find cheap airtight containers for individual spools of filament that fit.

This is a fitting for the Rubbermaid 21-Cup airtight storage bin that allows 1.75 mm 3D printer filament to pass through into PTFE tube without being exposed to air. It requires an M12 hole to be drilled into the container and the nut and bolt...

The build consists of : 3x These Filament Guide 2x Spool Rod Holders [thing:2460606](https://www.thingiverse.com/thing:2460606) 3x Spool Holders [thing:2459115](https://www.thingiverse.com/thing:2459115) 1x Sterilite 20qt Airtight Box (Target about...

3D printed parts needed to build an airtight dry box for 3D printer filament storage. Full instructions can be found at this link to my How-To at Instructables.com. The purpose of this dry box is to prevent printer filament from absorbing moisture in...

Just a airtight container, for food purposes.I hope you enjoy it ! ...Leave a "♥"

This part is based on the spooler for 1kg filament created by Tokyo_Bird, remixed to make it narrower so that two filament feeder can be placed in Asbell's sealed container. The filament feed hole parts was made from SubSite's [Dry Box with PTFE...

Then it can be glued into an airtight container so that you can print water sensitve materials. EDIT: i have added a file called Spool Wheel Claw. This item can be used to help the spools from wobbeling on the cone. pritn the file and then...

Super flat filament rollers to fit into the airtight enclosure for the airtight filament storage. ... for 1000 gamms (with paper Spool: PAPER-Tag) 1000 grams with normal plastic spool 500 gramms 750 gramms and 250 gramm spools (very tight tolerances but...

This filament Feed Through / Pass Through / Guide is used for printing directly out of my Filament Dry Box. The threaded inside part is printed from PLA and the Outside with TPU to seal up with the Filament. (Designed for 1.75mm). You just have...

I've used 1kg Hatchbox, esun, solutech, and atomic filament and they all work with this. Parts Required Container on Amazon (21 cup version) Desiccant (to keep things dry!) - a half gallon is enough for at least 8 containers. It keeps them at...

It's a handle for the airtight container without handle.

NOTE: All require print files (STL, STEP, F3D) and links to parts you may need are hosted on PrusaPrinters at https://www.prusaprinters.org/prints/110964-ptfe-feedthrough-with-debris-filter-for-airtight-3 Intro This is a 2 piece dry box feedthrough...

This is a replacement handle/clip for a reusable airtight container. ... Sold on amazon or other places under names like "Airtight Container Set for Food Storage"

Files are provided for single color prints, but the STL can be ‘split to parts’ in your slicer and made with an accent color as pictured if your printer is capableParts NeededRequiredPC4-M10 Male Straight Pneumatic PTFE Tube Push In Quick Fitting...

IKEA SAMLA is perfect container for 3D printing filament, though it is not airtight. Only two of these clips will help! This ultimate design pushes container lid hard towards container so it is firmly closed. It can be used for filament storage as...

I designed this container to hold Goop fish bait

This will replace the original locking handle for the containers that are about 5" square.I used PETG at 50% infill with 2mm top/bottoms and walls. ...&nbsp;I used supports and printed it laying down (in the locked position).</p>

Print the container body in PLA and the lid in TPU.

Easy to print and airtight 1.75mm filament feeder for dry boxes. No O-ring is needed. Both parts have small circular notches to firmly pinch the container wall and provide an airtight fit. ** Three versions are provided **...

Easy to print and airtight 1.75mm filament feeder for dry boxes. No O-ring is needed. Both parts have small circular notches to firmly pinch the container wall and provide an airtight fit. Three versions are provided: - Tight clearance (0.1mm), for...

Easy to print and airtight 1.75mm filament feeder for dry boxes. No O-ring is needed. Both parts have small circular notches to firmly pinch the container wall and provide an airtight fit. ... Three versions are provided- Tight clearance (0.1mm), for...

This is just another Silicagelbox for the "filament buffer (airtight, compact &amp; easy to fill)"It is a closed Constuction and with a Modifier, there is a Grid Put in the Lid.For printing, the Supports should be activated to everywhere and...

This is an airtight design for a filament drybox bracket. It uses a 2m thick 34mm diameter rubber gasket and 4mm brass inserts. ... My GrabCAD: https://grabcad.com/don-151

This solution allows each and every roll of filament to remain stored in an airtight container once and not removed until it has been used up. The filament is placed in an airtight “ ziplock or “press lock” bag, along with the axle and end caps and...

The canister is completely airtight except for the small hole in the end of the tubing where the filament exits. The hole is plugged by pushing the end of the tubing into the matching cap. If you would like your canister on a shelf above the printer,...