alexmos simple bgc 3 axis 32bit board and dual imu case 3d models

The knight and rook prototypes are currently still works-in-progress, but your thoughts are invaluable. I also plan to create this set with dual colors to open up even more customization possibilities. ...If you have any suggestions or insights, please...

The Y-axis bed connector I use comes from Tobi0892 design: https://www.thingiverse.com/thing:4316238 I am using a total of 35 chain-link (15 for Y-axis and 20 for Z-axis) and 3 chain-link-cut for the Z-axis. ... Edit: I added the file clip_connector,...

I made three covers to protect and finish the printer belt ends and rollers (y axis front and back, x-axis right side). Fits standard Ender 3. All covers just slide on and off, no assembly required. ... As my X-axis belt roller was slightly off-center...

High-quality enthusiasts seeking to enhance their electronic display experiences will be thrilled to discover this meticulously crafted board designed for integrating the DNA 200 mod into a comprehensive system. Featuring an adjustable aluminum...

3 and 5 axis robot arm 3 eksen ve 5 eksen robot olmak üzere iki farklı şekilde basılabilir ,kullanılabilir. Eğim amaçlı yapıldı. Montajı ve 3d baskısının kolay alınması göz önünde bulundurarak tasarlandı. Servo motorların kendi cıvata ve...

Dual Arm Mount for Raspberry Pi 3 (B/B+) and Pi 2 B+. Parts List: 4 - M3 Nuts 4 - M3 x 25mm Screws 4 - M4 Nuts for Arm side 8 - M4 Screws Directions: 1. Insert four M3 Hex Nuts into the bottom piece. 2. Mount Raspberry Pi to the bottom. 3. Most...

3 and 5 axis robot arm 3 eksen ve 5 eksen robot olmak üzere iki farklı şekilde basılabilir ,kullanılabilir. Eğim amaçlı yapıldı. Montajı ve 3d baskısının kolay alınması göz önünde bulundurarak tasarlandı. Servo motorların kendi cıvata ve...

USBASP Board Housing, One Piece Design, Screwless Construction. ... Print this housing vertically, then carefully insert your USBASP board into its interior.

this is a simple cable holder/guide for use with a direct drive. ...put/screw the holder on the carriage of the x-axis and fix the cable with a zip tie on it. looking for a simple direct drive mount? ...https://www.thingiverse.com/thing:4138063

This hanging bracket is split in two so it can accommodate your temporary struts while you’re starting out with your LowRider v3, and then graduate to your permanent struts once you get them cut and installed.Other details remain pretty much the...

... attach the holder to the carriage of the X-axis and secure the cable in place using a zip tie. In search of an uncomplicated direct drive mount? Check out this simple and effective design on Thingiverse: https://www.thingiverse.com/thing:4138063

Rotation indicators for Ender 3 Extruder and Z-Axis Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.1 Infill: 80 Filament: 3RDAX PLA Black Category: 3D Printer Accessories

It also adds more body to touch the X axis plate without the need for spacers or extra hardware to fit between and keep it more robust with less flex. Get other parts from the original thing. ... Compatible with: X:...

Since I'd determined the wireless part to use, I tried tape and other suggestions but didn't like any solutions, so I made a simple pad or spacer with holes, wire cutouts on the back, and round pegs to hold it in place. This could be made from PLA...

https://www.thingiverse.com/thing:3508682 Assemble is simple, requires a 5mm diameter bolt, a GT2 20T idler with 5mm bore and two M3 screws to attach to the 2020 extrusion of the printer. You'll need M3 drop-in t-nuts. ... Do not over-tighten the sync...

For the best results, print the plug upright and set the initial 50 bottom layers as solid, using a 10% grid infill pattern. ...This technique will create a dense foundation for the plug kit poker while allowing for a gentle press fit of the plug ribs,...

Post-Printing Sealing and fastening: Weather stripping will be applied to the board in the shape of each case. Wood screws will fasten each case down, pressing the edge of each case into the weather stripping to form a watertight seal. Each case's...

... as long as both sides are equal. After levelling the gantry, use the move menu to travel the Z axis all the way up and back down then measure it again. Keep adjusting until it stays level. ...The Z end-stop will need to be relocated as pictured.

... as long as both sides are equal. After levelling the gantry, use the move menu to travel the Z axis all the way up and back down then measure it again. Keep adjusting until it stays level. ...The Z end-stop will need to be relocated as pictured.

It was created with the "Simple CR-10S Pro Dual Z Sync Mod" by RickSisco in mind. The assembly process is uncomplicated, requiring a 5mm diameter bolt, a GT2 20T idler featuring a 5mm bore, and two M3 screws to secure it to the printer's 2020...

Very Basic concept layout of a Roll-Pitch-Yaw mount.IF this were actually used, it would need to account for bearings/dampers and any applicable offsets to align the axes of rotation with the actual axes of definition (usually through the center of...

By using the $20 GT2 upgrade parts from http://www.printrbot.com, I combined the X-axis extender mod and a GT2 modification to eliminate X-axis slippage during printing across the entire build plate. These upgrades may still be printable on a...

This is only half the solution to this, I use 2 sensors, one for the left and one for the right side of the CNC (reason for these parts.) I then have a custom homing code that seperates the two Y-axis into a distinctive Y and U axis, the CNC then...

I made significant changes to the Pi Zero case and lid by red9987 and cfunseth in order to enhance their functionality and usability. I recreated the design using 123D Design, making substantial modifications along the way. Firstly, I added a power...

I designed my very first Raspberry Pi 3 Model B case.

I wanted to make some changes to the Pi Zero case and lid by red9987 and cfunseth. I re-created the design in 123D Design and made some small changes. The first is a power logo on the lid, to indicate which of the two micro-USB ports was for power,...

To minimize support material and make printing smoother, the VESC case can be oriented upside down on most 3D printers, including LulzBot Mini models, when printing on a standard-sized 6x6x6" build area. When preparing for assembly or repairs,...

Inertial Measurement Unit (IMU)

... secure the cap when printing. Try both with and without a rubberband, it works well for me. I've also added versions for simple z-axis (https://www.thingiverse.com/thing:2426084) and Stabilo Pen Storage (https://www.thingiverse.com/thing:2431999).

I printed the box in PLA at 25% infill. The lid I loaded into Meshmixer and beefed up the tabs that clip into the box and I also trimmed down the height of the air channel as it was hitting my board when it was mounted. ...I printed the lid in PLA with...