allen wrench key 3d models

This is a short 2mm metric allen wrench.

ratchet.stl is a one piece ratchet for small Allen wrench keys, and then you print adapters depending on the wrench size. ratchet2.stl has 6 inner blades instead of 4, and they are a bit thicker, try it in case ratchet.stl wears out too fast and...

This is a short 4mm metric allen wrench.

This is a short 2.5mm metric allen wrench.

This is a short 3mm metric allen wrench.

This is a short 5mm metric allen wrench.

My wife dropped an Allen Wrench from my pocket into the dryer. It cost me time and money to fix the dryer. I modified this design to hold the wrench more secure. My original design kept breaking where it attached to the key ring. I added the zip...

This is a short 5.5mm metric allen wrench. ...

This is a short 3.5mm metric allen wrench.

This is a short 1.27mm metric allen wrench.

This is a short 1.5mm metric allen wrench.

This is the full set of metric allen wrenches from 1.27mm through 5.5mm. ...

Handle for Allen/Hex Wrench/Key with removable chuck for different sizes

Allen wrench holder with some improvements: Will not wear out, holds hex keys in with an o-ring, not tension in the plastic All Allen wrenches equally accessible 3D printable Uses a standard o-ring available at most any hardware stores Why did I make...

Handle for Allen/Hex Wrench/Key 1.5-4.5mm This clamping chuck breaks lips. ...So I created my own https://www.thingiverse.com/thing:2920086

English and metric allen wrench holders for a pegboard with 1in spacing. Inspired by the excellent drill bit holders by ckirby: http://www.thingiverse.com/thing:1003471 You'll need 2 clips for each holder. ...Public onshape design is here:...

Just a simple set of T handles for smaller Allen wrenches (fits M1.5, M2, M2.5, and M3). Some are a bit tight, but that's intentional. ...Push your wrench in from the bottom, twisting as needed to "drill" through the tight plastic, and secure it in...

Instructions The best approach is to use the customizer, although you can download one of the STL files if it matches the size of your key. To use the customizer, measure the width of the key, when rotated so it's the widest (as shown in the photo...

The included .scad file allows for custom wrenches to be generated with variables for thickness, short and long arm length, and the bend radius. ...Print Settings Printer: Wanhao Duplicator i3 ...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:151461 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=151461 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:151461 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=151461

A removable, customizable-sized handle for hex keys/allen wrenches. The hex key locks into place when in use, but can easily be removed to use the wrench without the handle, in order to reach tighter spaces. The handle can be custom sized in diameter...

I suspect that if the slope is on the "bottom" it will be easier to insert and harder to remove the keys, so the model should be "flipped." Added a "toggle" for the groove to be angled or straight as in the original. "Standard Set" stls (The...

I changed the code to bend the hex key the right way. ... to use you will want to download the openscad filen and only generate the hex key size you want, as them all together might not be printable. ...

This hex key was made to use with https://www.thingiverse.com/thing:2528748 print the 2 parts and glue them together.