aluminium tubing and connectors 3d models

As it is I use the slic3r PE 1.41, which has a feature to click a face and make it the bottom. Here's what I'm using for 1"/25.4mm steel tubing: center cube: 24.6 protrusion: center: 22.6, end: 22.2, length: 33 spacer: 5 rounding: 1.5 Print...

I'm using 25.4mm/1" square steel tubing and the inside size is about 22.2mm. Make the inside size a bit larger near the center and then taper it down to the end, which means you might need to pound it in for the last bit. It also means it may be hard...

This can be customized for all sizes in the customizer Instructions Print in the current orientation (don't rotate it over the x or y axis) for strong connectors. Fill pattern: Concentric Shell pattern: Whatever looks nice Shell: 1 or 2 layers...

The STLs are for 10x10mm aluminium bars with an inner dimension of about 8x8mm. This can be customized for all sizes in the customizer Instructions Print in the current orientation (don't rotate it over the x or y axis) for strong connectors. Fill...

The SCAD has callable modules to model the connectors and the tube profile and a print module to split a part in half and rotate for 3D printing. Work in progress, probably needs refining. I'm also working on a hollow version so cables etc can pass...

This provides the complete set of all nine possible square tubing connectors. Also provided is a special fixture to allow you to find the optimum fit for your tubing. The default STL files include all the fittings for 1/2 inch (12.7 mm) square...

Printer Enclosure using 1" Square tubing from Home Depot. ...Print and use the connectors as shown. I assembled using a #8 x 3/4 Phillips Head Screws. Size the tubing as required. ...Use Lexan or Paneling of your choice to cover the enclosure.

... - Dual 3mm screw holes on the shelf supports for two screws, or one nut/bolt through the PVC. - 5mm screw holes on the base of the shelf supports. This is a work in progress, and I'll add more file builds as I find them necessary to make.

I was not able to find modular connectors for 25mm rounded square tube aluminium and designed these for a project I am building for a draw system in the back of my Suzuki Jimny. ...

PIPE AND TUBING

This is my version 2 (and a lot better) of previous connectors for 15mm x 30mm oval aluminium tubes. ...This has better support for the aluminium and slight bigger holes for screws (version 1 tent to crack when screwing).

Outside table made from aluminium tube and beech wood slats.

This is a little project i worked on bc i had this square tubing that is 3/4 of a in big and i need a way to put it together so i made my first ever design and this is the outcome. Let me know if something does not work. Also this is kinda a work in...

This is a sphere connector with isometrically aligned holes and rod kit for small constructions.

To fix it inside the tube i used self-tacking screws. ...Print Settings Printer: CTC Bizer Dual Rafts: Yes ...

Snap together and bend up to 90 degrees. ... 5 point and 3 point connectors could be used for icosahedrons, dodecahedrons, and other shapes.

T and X connectors for a wooden shelf thickness of 19 mm, maybe 18 mm and 20 mm can work. ...Test it !

I started out by recreating MT30 male & female connectors which are so accurate they fit the real connectors, then used those models to create a mount which can hold either connector. The mount holes are 18mm apart for M3 bolts. Included are a...

You can find a rough build guide on my blog here: http://style.oversubstance.net/2020/08/create-a-hue-compatible-diy-led-light-sculpture/ The frame is made out of pieces of aluminium LED profiles that are kept together using the corner and end...

Connectors (2 back to back) go into slots and connect walls and/or columns. No glue required, but the two rails may be glued back to back End pieces go into the same slots and close them for aesthetic purposes or increase footprint for stability. 4...

4 supports: vertical and horizontal connection tabs left and right positioned 7 connectors, straight and 90°, all of them with vertical or horizontal tab placement. i also include the smatphone holder the connector and the tomtom XL holder. all...

these are some supports and connector i designed because i need some of them to replace my 12 yo tomtom with a smartphone to be used as a navigator and speed meter (very old but still functional samsung galaxy s2, maybe in the future i'll switch to...

Some connectors/supports for Mountaineers to help make the mountain boards more stable.

there are a total of 19 connecting pieces: slot nuts, corner connectors, extension plates, etc the sliding blocks are available with and without nut (M3). without nut, simply screw in the screw. for better hold and for frequent use, please use the...

This is my version 1 for 15mm x 30mm oval aluminium tubes. Check for my version 2 (better) of this thing. ...http://www.thingiverse.com/thing:1063923

A bamboo and aluminium clock with a cork backing. ...The aluminium is milled, the bamboo is CNC routed, and the cork is lasercut. Dimensioned drawings and .stl files provided. ...Designed to suit takane brand clock mechanism, unknown if others may fit.

The STLs are for 10x10mm aluminium bars with an inner dimension of about 8x8mm. This can be customized for all sizes in the customizer. ...

Customized version of https://www.thingiverse.com/thing:3184300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3184300

Customized version of https://www.thingiverse.com/thing:3184300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3184300

Customized version of https://www.thingiverse.com/thing:3184300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3184300