amscope camera adapter 3d models

McMaster part numbers are: 10-32 nuts: 91841A195 10-32 screws: 92949A269 1/4"-20 nuts: 95462A029 Keep in mind that my base-station mounting method might be different from yours, but the mount is universal for camera bases. I'm using a Manfrotto Mini...

The original Vivitar Tripod quick release adapter was missing, so I created a replacement model using Sketchup. After three iterations, the third version worked flawlessly. To ensure precision, I employed a vernier caliper to measure critical...

Two versions of this build are available, one featuring a 2-thread design that uses a single piece print and another that incorporates an adapter for a 1.25" eyepiece, requiring multiple prints to be glued together. Both options function seamlessly...

I needed a camera for Octoprint on my C.H.I.P., so I found an Xbox Live Vision camera at a pawn shop for about $5. It works great in Octoprint, but I wasn't fond of the mounts that were available. This uses a GoPro style mount, so you should be...

I couldn't find an easy and a fast way to attach the articulated camera mount by Sneaks onto 3030, so I made one myself.Takes a bit of force to clip on, but even if there's little wiggle room, it sits there sturdily enough and can be slid...

However, if your printer has different hole alignment than the original models - and I know some people have experienced this issue firsthand - don't worry, I've created this adapter to ensure compatibility without modifying the original file or...

I upgraded from Arlo cameras to Reolink PoE after Arlo kept asking for more and more money. For the back of my house I decided to use a single Reolink Duo. I initially tried to mount it from the eve of my house, but the mount wasn't designed to...

that happened to me], I made this as an adapter to allow other folks to use it too without changing the original file or discarding the original print. I used a couple metric socket screws (4M .7x8mm) per the image above. They just screw directly...

This is a cartridge and back that allows you to shoot 35mm film in a Polaroid pack film camera in 3.5 X 10 cm format, exposing the sprocket holes as well. Print the back with supports. Print 1 of all parts and 2 of the spool top. Print the knob...

I remixed the front holder. ...It is easier to print and fits better.

This is a remix from this: https://www.thingiverse.com/thing:5334319 I further reduced the height so it takes less time to print. You could play with infill as I did but it might no be necesary. Uses a M8 bolt with a washer at the screw...

I will be using my scope everyday and didn't want to be bothered with uncover the whole thing everyday so created these dust caps for the lenses. Uploaded both with and without the eyes. If you're going for the dual color swap print at .2 layer...

Resized to 200mm diameter to fit the bed of my printer. ... Center hole is 32mm.

I designed this feature to prevent the dust cover from constantly being put on the microscope. ...A snug fit is achieved, but it's essential to secure the eyepieces with screws to avoid them getting dislodged when removing the cap.

Impression sans support, reglage classique. ...Rien de special ;-)

... the 10x eyepieces most of the time. ...So i needed somewhere to store the 20x (WF20X) eyepieces So I have made a case and lid to protect them. I am pretty sure this will also fit the SE305 and SE306 eyepieces and certainly other AmScope models too.

This adapter aims to allow an affordable and much lower barrier of entry for hobbyist and professional repair technicians to get a high quality articulated arm setup for their microscope. Any articulated arm that has a vesa 75 mounting bracket...

These handles attach over magnification and coarse adjustment knobs on an AMScope SM-1TNX-144-M microscope but may fit similar models. ...The teeth's interlocking design seamlessly merges with the microscope's pattern, creating a secure fit achieved...

Raspberry Pi Camera Board Adapter Mounting Solution.

19mm micro camera to grl frame adapter

... it easier to fit the cap on the eyepiece and reduces the damage to the rubber part from the sharp edges. The cap also fits my Amscope stereo microscope with a slight slack but serves as a perfect dust cover. ... Print with the flat surface down.

This is the adapter required to attach this lens to a Nikon F-mount camera. It allows you to take 4x macro shots. ...To read a review of the lens, check out this link: https://www.closeupphotography.com/seventeen-dollar-plan-4x-lens/.

Adapts micro cameras to the V1/V3 obsession roll cages

Adapter for Mi 360 Home Security Camera on 1/4″.

zwo camera and nikon f mount adapter+drawer

adapter to attach the vista hd camera to the obsession

Print with TPU at 80% infill.

To comfortably hold your iPad with its cover securely attached, consider investing in a sturdy back holder that will keep your tablet firmly in place even at lower angles of use.