amscope camera adapter 3d models

The mounting hole diameters were enlarged and the back was flattened slightly (though it's actually very concave) so the camera can snugly sit into any corner without rotating. A cupped rim extends just past 180 degrees to keep the ball mount...

The normal design is ideal for general use, while the shortened version offers a more compact solution that allows a micro Swift 3 to fit snugly on Rooster frames alongside a GoPro lens, providing ample protection for your camera. Hardware...

However, one of the lights didnt have its metal adapter threaded for 1/4" screws. I couldn't find my tap and die set, so I just 3d printed an adapter to replace it. It should fit most ball adapters. ...I did this for me, maybe some else has a similar...

Here is the spun text: DIY Adapter in Minutes: Clone the Pentax K-X AC Battery Adapter. Score: 0.15 Infills: 10% Supports: None Brim: Disabled Use two 6x40mm springs to create contact points, solder thick wires and thread them through a hole -...

Lens cap attachment for Canon Rebel EOS T6 camera (58 mm). Fits snuggly and can be printed with any FDM printer. ...Fits along neck strap by fitting strap into grooves.

Use this easy to print model to place your Raspberry Pi Camera to any tripod (M6 thread) Model in Fusion 360 is in [this thing](https://www.thingiverse.com/thing:4883302)

Use this easy to print model to place your Raspberry Pi Camera to any tripod (M6 thread) Model in Fusion 360 is in [this thing](https://www.thingiverse.com/thing:4883302)

Das Gehäuse mit Halterung findet man hier: https://grabcad.com/library/raspberry-pi-camera-v2-case-and-mount-1 Print SettingsPrinter brand: AnycubicPrinter: VyperRafts: NoSupports: YesResolution: 0.2Infill: 40%Filament brand:anyFilament...

This is a remix of the back of the camera case from here https://www.prusaprinters.org/prints/3407-articulating-raspberry-pi-camera-mount-for-prusa-m which turns it into an adaptor for the high quality raspberry pi cam case found here...

My Raspi Fisheye camera is a little bit smaller and therefor did not hold in the slots. I made the slots tighter for a snug fit. ...The width is the same, so the other cams should also fit.

Use a microscope lens with a micro four thirds camera! This works with finite objectives with 0.8 inch rms threads and 160mm tube length. ...Infinity corrected objectives would need a tube lens.

Adapter -> box screw recesses are for standard 6-32 screws which are typically used for mounting outlets and switches to wall boxes. The mount plate -> adapter holes are sized for standard switch or outlet faceplate screws. ... Interior height is...

This adapter is specifically designed to work seamlessly with an Orion Telescope's Newtonian model, both the 8-inch and 10-inch varieties.

This Adaptor lets you hook up GoPro Mounts to any action camera with a tripod screw mount, no matter what brand it is. Make sure to print at 100% infill or the tripod thread might snap off and get lodged in your camera's bottom. However, printing at...

This print is to allow the use of high quality pi cam with the articulating camera mount. This is a remix of the back of the camera case from here https://www.prusaprinters.org/prints/3407-articulating-raspberry-pi-camera-mount-for-prusa-m which...

... for easy tension release and cable organization. Overall, I'm thoroughly impressed with the HM1355 camera module's performance and would highly recommend it to anyone looking for a reliable and affordable webcam solution for their OctoPrint setup.

Here is a rewritten version of the text in American English, without foreign characters and with active voice: A custom RaspiCam Telescope adapter for 1.25" eyepieces has been created by redesigning an existing model from Thingiverse (1812708). ...This...

... Secure adapter over eyepiece and take pictures, black felt may be added to reduce sunlight seeping. Works well with 1.25" eyepieces. Watch solar observing on Ustream for device demonstrations. ...Link: http://www.ustream.tv/channel/solar-observing

Adapter Plate: 2 Pack External Hex Screws M4 x 20 mm 2 Pack Nut M4 2 Pack Washer M4 x 12 mm Wall Mount Bracket: 2 Pack 4 x 30 mm Wood Screw

Webcam adapter/holder for Ender 3 pro. Can be attached with original screws either to the clos pair of screws or the further. ... OctoPrint timelapse with the setup: https://youtube.com/shorts/NGqXB7mLigU?feature=share

Wanted to run the Foxeer Cat 2 on my Taycan but surprisingly (for me at least) it didn't fit. ...Now with this adapter it does and looks pretty OEM.

I'm designing a compact camera setup for my Furibee X215 drone. The ideal placement is between the egg frame, where two holes can be utilized for mounting purposes. I've since updated this design with additional modifications on June 14th, 2018, to...

This is a quick Tinkercad design to solve the issue of the Logitech Brio 4K Camera mount covering a small amount of the top of the Alienware AW3424DW OLED Gaming Monitor. I used Prusa PETG in Black. ...Pictures are in draft mode but works well.

Use Nikon lenses on the HQ camera (Cmount) Print instructionsprint at least in 0,1 mm layers. I used a -0,1 horizontal expansion on my Ultimaker2 to get the fine thread to fit, some other printers may need a bit more correction.

An expandable cap for the printer frame covers sharp edges, concealing them from view and can be extended with a camera arm. With just 0.2 mm between components and frame it fits perfectly, snugly in place. Only two bolts or nails are needed to...

Use high-quality Nikon lenses with your HQ camera's C-mount. Ensure that prints are created in layers as thin as 0.1 millimeters. To achieve precise threading with your Ultimaker2, apply a horizontal expansion of -0.1. ...However, other printers may...

I have a lot of camera tripods, and don't need another one. This will suit Roland Handsonic HPD-20, SPD-20, SPD-SX, APC-33. It might also work for Yamaha DTX-M12, and other multi-pad mounting plates. ... If you want to print the plate as well,...

I wanted to share with you guys a very simple self-made design that I use to attach my Rode Wireless Go microphones to my camera. I just sometimes wanted to be able to transport and use both of them at the same time, without needed to attach the...

I designed this component specifically for adapting a Caddx Ratel to my rooster's setup. To complete the project, you'll need to add some thread inserts, which I personally sourced from Inland Carbon Fiber Filament. PLA or PETG will also yield...

A Customized Focal Reducer for the Skywatcher 8x50 Finder Scope Finder Scope Details: Outer Diameter: 50.7 mm Pin Hole Size: 0.75 mm T2 Adapter Specifications: Outer Diameter: 42 mm Pin Hole Size: 0.75 mm Print Settings: Printer Model: Geeetech Prusa...