anet a12 3d models

This may only provide charging at 500mA, but you're sure that no one messes with your phone! Connectors are easily available from eBay for cheap in bags of 10... I just pushed the wired connectors in (both go in from the female side) and filled the...

So I needed a battery charge and test setup. I build a charger holder around my battery booklet thing: https://www.thingiverse.com/thing:4113164 This adds a piece for the TP4056 in front of the holder and some slots on the sides for the cables. I put...

... one out and let me know how it goes as I am concerned how well it'll stay on the metal tube when air is forced through smaller openings. Print Settings Printer: Anet A8 Rafts: Yes Supports: Yes Resolution: 0.2 mm or 0.3 mm Infill: 20 - 30 used %

halten auch sehr schön daran. Die Kronkorken kann man mit der Zange anbördeln oder lässt sie einfach vom Magneten halten, dann kann man immer mal wieder wechseln. Lässt sich ohne Support drucken. Print Settings Printer: ANET A8 Plus Rafts: No...

This is a remix of jag's "Parametric Flyswatter" (https://www.thingiverse.com/thing:9927). I just fixed the bug that the corners were not rounded properly when creating rectangular fly swatters instead of quadratic ones. Also fixed a problem that...

If you want the lid to shut tightly, you'll need to make some cuts in its separating plates, as can be seen in the last image. Thingiverse removed the commas from the filenames, so to be clear, measured at the top, the sizes of the three boxes are...

They all fit perfectly and the box can be turned upside-down. I used https://www.thingiverse.com/thing:2027087 to create STLs. I also added a tray for longer tools. Print Settings Printer: Anet E10 Rafts: NoSupports: No Resolution: .3Infill: 25%...

... shapes! Also increased the sizes and made some minor tweaks to make cutting out cookies a little easier. Print instructionsUnassociated tags: cookie cutter Category: Kitchen & Dining Print Settings Printer: ANet A8 Resolution: 0.1 Infill: 10%

These files should work well for resin printers, too.I use two printers, an Anet A8 Prusa clone and an Anycubic Vyper. ...The model has printed well on both of them using PLA and PETG.Note that the resolution of the design is high such that printing it...

Print Settings: Printer: Anet A8 Rafts: It doesn't matter if you use them or not. Supports: You don't need any supports for this guide. Resolution: Set the resolution to 0.1mm for optimal results. Infill: Use 100% infill for a solid and durable...

... The rod diameter is 8mm. The following rod lengths are needed; 113,7mm (4x); 81.6mm (2x); 35.3mm (2x).] Print Settings Printer Brand: Anet Printer: A6Rafts: No Supports: NoResolution: 0.2 Infill: 40% Filament: eSun PLA Category: Household

In addition, those two versions have wider gaps less likely to fill in with wide extrusions widths. You can see the cover in place in this video: https://www.youtube.com/watch?v=IG5YceFKt48 Print Settings Printer: Anet AM8 Rafts: No Supports: No...

I print this on my Anet A8 with 0.2mm layer height to get the twist lock portion to work well. The base prints without supports, but I did use some on the globe with overhang angle up to 75° just to get a little help towards the center of the...

Can be found here on Cults: https://cults3d.com/en/3d-model/game/piggy-van Explosion diagram in 3d viewer (Sketchfab): https://skfb.ly/6W9wB 10x10x6cm, 70g. Print instructionsPrint Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No...

Charging dock for ZTE Axon M phone. Will hold your phone in the charging dock or on the front, folded, and open. You can access full screen and buttons when in docking station. Print Settings Printer: Anet A8 Rafts: NoSupports: No Resolution: ...

Print Settings Printer: Anet A8 Resolution: 0.2mm Notes: It's modeled at full scale - simply scale it to whatever size you need; same for the pilot. For the electrical wires on the full-scale model, they're approximately 3-4 mm thick, and the...

**Print Settings** * Printer: Anet A8 * Rafts: No * Supports: No * Infill: 50% * Notes: All parts were printed using ABS. The extruder was set to 247 degrees and the bed was set to 105 degrees. All prints were created with a 10mm brim. The only...

To attach my enclosure to my Anet A2 frame, I used 5mm long M3 screws. This case fits the Arduino Uno board perfectly, with pegs that keep it in place but do not prevent it from falling out if tilted beyond a 90-degree angle. ...To address this issue,...

This is a Thermometer box connect frame slider by magnet I design this so everyone can using magnet to bring or connect to every location on the frame of the 3d printer machine Print Settings Printer Brand: Anet Printer: A4Rafts: Doesn't Matter...

This design is meant to replace both the bearing and pillow blocks on my ANET-A8. I'm also using it on the X-Axis of my RepRap-8 (https://www.thingiverse.com/thing:2562389). The design includes both the bearing and the pillow block, offering several...

You will need some wire for the spring of the negative pole and some metal sheet for the positive pole.Feel free to use and customize the design. I've published this design first on Thingiverse. Print SettingsPrinter:ANET...

I was inspired by the concept of the door with hinges, but struggled to find one that could accommodate the Anet board. To fit an extra mosfet for the heatbed, it's slightly larger than the original design. You'll need 8 M3x10 screws and their...

Hold together by some rubber bands, with an indent on the back to push the cards out. What you see in the pictures is my version 2, which already survived about 6 month daily use on my pocket - you can call rod an approved design;-) Designed in...

If you have any questions, rest assured I'll answer them promptly; feel free to ask anytime.\n*Updated version coming soon\nPrint Settings\nPrinter: \n Anet A8\n \n Rafts: \n Doesn't Matter\n \n Supports: \n Doesn't Matter\n \n Notes: \n Printing...

I got mine here: https://www.aliexpress.com/item/1005002907154467.html (not affiliated) It is listed as an 'MK8 Upgrade Direct Drive Hotend Kit 3D Touch Mount 5015 Pulley Turbo Fan Extruder For Ender-3 CR-10 CR 10S/PRO Anet A8' Three parts to print,...

In the end: this is iteration 2 and it works surprisingly well :-)\r\n\r\n150 Minutes print with three shells and 26% infill.\r\nDesigned to print without support with only slight bridging challenges for the internal water path.\r\nWorked fine on my...

The model is designed for Anet A8 and PLA plastic (printing with cooling). Printing with support. For the base, we take a ratchet cloth SERITHANE (Italy), and 4 bolts 3x12 for fastening. The ratchet cloth SERITHANE (Italy) comes in different colors...

On my Anet A8 printer, I can slice out a 90-degree section and print four of them, which all fit together with minimal excess space. ... In addition to existing variables, ANGLE can be set to any value that fits on your printer: 360 equals one whole...

Impreso con Anet A8 con altura de capa de 0,2mm sin soportes. Lo he impreso con 100% de relleno para tener más consistencia. El dispositivo tiene unas dimensiones de 54mm x 38 mm x 6,5mm Actualización: Se agrega el mismo dispositivo con el logotipo...

You can get one for less than 1€ example:...