anet a6 auto level 3d models

The adapter will allow the mounting of an MKS Gen L board to the standard Anet A6 mounting holes. Hardware: 4 x M3x16mm screws 4 x M3 nuts 4 x No.4x9mm flange screws (but you could try the M3x12mm screws from the kit) Print Settings Rafts: No...

This is my take on a magnetic fan holder for the Anet A6. I'd grown tired of having to disassemble the printer halfway if something went awry again. The magnets in question measure Ø6x3 mm and are neodymium, top-grade. Thankfully, everything seems to...

Printer: Anet A6 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Grid Notes: Printed with a retraction setting of 1.5 mm using fluorescent green plastic filament, brim used for bed adhesion but may not be necessary. Post-Printing **A Few...

Here's a comprehensive list of parts used for this project: * 2x Teflon tube holder clips (3-4 mm) * 1 piece of Teflon tube (3-4 mm) compatible with 1.75mm filament * Linear bearings from the Anet A6 printer (LM8UU, 2x) * Extruder driver gear from...

------------------------------ My Anet A6 Y Axis Face Plate is close to wearing through the upper left guide rod. I decided to combine a design I had printed for added strength with the original face plate. Additionally, I took this opportunity to...

Carcasa para la fuente original de la Anet A6 un interruptor con fusible y un medidor de voltaje y consumo. Idea original de MartinS79. No incluye los taladros para los tornillos, veo preferible mecanizarlos en la posición exacta. ... *Interruptor:*...

Here is a mounting bracket to mount E3D hot end to Anet A6 carriage using existing screw on the bottom of carriage and M6 X 30 throat sticking at the bottom. Props: Mounting an E3D titan hotend to your Anet A6 carriage just got a whole lot easier...

The additional 'Controller housing with cutout' is compatible with the Anet A6 X-axis belt tensioner mod: https://www.thingiverse.com/thing:3713816 It's recommend to use a separate 12v power supply 1A or greater. Because when connected to the...

A Simple Solution to Cable Management for the X Wagon One of the main issues with the Anet A6 printer is that the cable to the X wagon gets stuck during higher prints. This simple solution addresses that problem. To use metal spacers between moving...

Utilising the free space under your Anet A6, this box allows you to keep stuff stored, like spare pieces, old pieces you don't want to throw away, or whatever else you need. (Personally, I think it is good for things you won't be using often but...

... to make insertion easier and prevent damage to the bushing. Push the bushing between the guide rod and the frame plate, then remove the brim with a sharp knife. You'll need 16 bushes in total to provide all the rod connections for your Anet A6.

This is a Backcover for the LCD Screen on the Anet A6 with integrated Raspberry Pi Zero W and RPi Camera 1.3. I run OctoPi on this Raspberry. January 19, 2018: Added a version with just 3mm holes instead of M3 nut inserts. You will need: • Raspberry...

A YouTuber created an excellent video about this design: https://youtu.be/R4o64xEV-hg If you appreciate my work and would like to support it, please consider donating through PayPal: https://www.paypal.me/JordanHogetoorn Print Settings: Printer:...

Unobtrusive Anet A6 X-axis Belt Tensioner This parametric design creates an x-axis belt tensioner for the Anet A6 3D printer. It was made with FreeCAD 0.17 daily. The goal was to create a tensioner that requires minimal changes to the original...

Unobtrusive Anet A6 X-axis belt tensioner This is a parametric design for an x axis belt tensioner for the Anet A6 3d printer. It has been made with FreeCAD 0.17 daily. The design goal was to create a tensioner which requires the least changes to...

Here is a Y-Axis Cable Chain for an Anet A6 printer. I was unable to find one on Thingiverse so I took it upon myself to Remix RotoScan generic chain. Demonstration link: https://youtu.be/PpistVXVouQ I was printing a Thing about a week and a half...

I designed this device to align my bed perfectly with its axis. ...Additionally, I utilize auto-leveling, however, my Y-axis was not parallel, which I discovered during the printing of my creation. ...Therefore, I was able to resolve this problem.

Another Anet A6 Hot End Modification for a New Printer. The goal is to enable ABS, PET-G, and PLA printing. This setup allows the use of an hot end with a heat break like the E3Ds. The extruder now sits on the back of the printer frame, connected via...

I'm reflashing it with an arduino as ISP Configuration Of course you need : #define BLTOUCH Probe offsets (you may have adjust the Z position to you own probe z offset) : //ANET A6 with BLTouch/3D-Touch Front mount // (mount:...

There are various covers available on Thingiverse specifically designed for the original Anet A6 power supply. Note: The pictures shown above are from my previous version of the power supply cover before I integrated the power supply bracket. The...

... your printer after making any changes to ensure optimal performance. By following these simple steps and tips, you'll be able to upgrade your Anet A6/A8's filament holder for improved printing quality and reduced downtime. ...Happy printing!

These are custom covers for the Anet A6 X axis right and left support systems. They can be attached directly to the X rod with ease, providing a sleek (dust) cover that conceals the internal mechanisms of both supports. The right-hand cover proudly...

Filament spool holder designed specifically for Anet A6 printers. The holder is situated behind the display at a precise 35-degree angle, providing an effortless way to change filament spools while optimizing desk space. It accommodates spools with...

... at first glance, safety should always be the top priority. By combining this rewired strain relief with a cable chain, I've effectively eradicated two major points of failure on my A6 printer while maintaining a secure and organized cabling system.

Decided to create a new support for the BLTouch on the original Anet A6 carriage but unfortunately the existing designs didn't meet my expectations. So, after many failed attempts and reprints, I designed this one from scratch to get it just right. ...

Print Settings: Printer: anet a6 Supports: Yes Resolution: 0.2 Infill: 100% Notes: It's crucial to use 100% infill to ensure the model is strong enough, so I added some support columns to prevent sagging on the overhangs. ... I created this design in...

It fits on the 8mm thick acrylic frame plates of the Anet A6 and A 8 printers 6 PTFE tubes with an outer diameter of 4mm can be clamped and one tube end cap when it's not in use. The end caps closes the open tube end to keep the filament dry...

Most BLTouch / 3DTouch mounts for Anet A6 are attached to the blower fan plate, causing potential loss of sensor accuracy due to vibration and stresses applied to the plate. I developed a mount that attaches directly to the X carriage, bypassing the...

... guide, and you have to change the partition, and print the version with a clearance, wearying pass the screw and nut that outside. For those who have an older version of A6, here is the Henkolizer version: http://www.thingiverse.com/thing:1974412

... nozzel) If you use another setup pls. verify these values for your printer. Update 24.03.2021: With Version 1.1 for my Anet A6 now the distance between nozzetip and lower side of the probehull is now 8.3 to 8.4mm...as it should be like I read :-)