anet a6 upgrade extruder 3d models

I reinforced metal for the Frame of my Anet A8, which greatly improved the stability of the printer, especially on pieces with greater height and high speeds. I achieved good results at 120 mm/s speed. The best improvement I made to print at high...

Because of the small size of the extruder button, I advise using a Layer Height (quality) setting of 0.1mm and a print speed of 40 mm/s for optimal results. It's also smart to use a "skirt" as your build plate adhesion method. Don't be shy about...

I've been dealing with issues where heat starts creeping up my throat, and neither my fan nor heatsink is mounted due to limited access to the extruder mechanism without a complete teardown. So I found the KISS fan mount created by aeropic, but I...

Having some test prints on my Anet E12, I discovered warping effects on the opposite side of where the fan was blowing to the nozzle. Not finding any radial vents in Thingiverse for the custom fan, I came up with one myself. Starting with reusing a...

I eventually came up with this idea, which consists of two parts and is designed specifically for standard Anet steppers. As usual, I used sintered bronze bushings throughout. I produced versions with 4 and 3 bushings, but since the rods aren't...

... allows the fan to point straight into the fins with a little space. I think this is a better solution. Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 100 Category: 3D Printer Accessories

ENG: This is a straightforward pushbutton for the extruder screw. It's painful to press without a button. <h1>ESP:</h1> Un simple botón de empuje para el tornillo del extrusor. ...Duele cuando no hay un botón para pulsar.

Extruder fan silencer mod, bolt on top of your 50mm radial fan to bring down DB. On my setup from 30cm away Without Silencer: 65DB With Silencer: 57DB Bolt mounts are wide enough for M4 and are 2mm thick. Print to the quality you require,...

I designed a simple cap using Fusion360 that helps release the extruder gear when loading and unloading filament. It's especially useful when you struggle to get the filament to feed through properly. Without it, the hex head tends to dig in too...

I added a piece to stabilize the slight rotation of the extruder motor around its locking screw during sudden changes in direction. ...This allowed me to reduce even more the remaining wobble I had after separating the X-axis from the infinite screws of...

I Designed and Built a Custom Mount That Attaches the Extruder to the X-Axis, Enabling a Shorter Bowden Tube for Improved TPU Printing. This Innovative Solution Overcomes the Limitations of Traditional Mounting Methods, Resulting in Enhanced Print...

... suit specific needs, like mine, where a rapid connector features an M5 thread, whereas the standard component has an M6 thread. ...The spring guide is integrated into this design. This customized part significantly enhances the extruder's performance.

I recently expanded upon the Extruder Fan Mod V2 by hadoko and printed the whole thing with carbon fiber. ...Removing the support structure requires a bit of finesse, but once it's done, you'll have a sleek addition to your 3D printer, smiling.

This is a compact device specifically designed to fit onto the A8 Extruder, making it easy to implement repairs or adjustments as needed. ...Simply warm the printer up and carefully position the tool at the rear of the A8's stepper motor.

The design incorporates a straightforward bracket that secures to the extruder stepper motor, effectively alleviating pressure from the main loom's connectors as the carriage navigates its path. ... Manufactured using ABS material with a 0.2mm layer...

This conversion grants unrestricted access to the extruder drive. The concept originated when I viewed the design of SentinelRX5. https://www.thingiverse.com/thing:1749614 Installation is straightforward and completed within minutes. The part was...

reposition of the extruder fan to allow visual access to hotend and filament.this thing adds an aluminium heatsink and moves extruder stock heatsink and fan 23mm far and 20mm right from extruder motor allowing for visual inspection of the extruder,it...

2x M3*18 for the extruder 2x M3*20 and 2x M3 nuts for the hinge, fan, and heatsink 2x M3*18 for the duct fan and stationary hinge Credit is given to the original creators: https://www.thingiverse.com/thing:2290361...

This setup enables easy placement of the extruder cable underneath the plate, eliminating interference with buttons or display and reducing the likelihood of snagging during printing operations. ...By routing the cable through a large hole in the upper...

Originally took inspiration from https://www.thingiverse.com/thing:2380825, but decided that I didn't like how it attached to the upper bolt as I have a cable clip located there, it was also very brittle in the arm so I redesigned it to allow the...

... These spacers ensure optimal alignment of the bracket's mounting points with the existing holes on the Anet A6. ...The bracket securely fastens to three strategic points on the frame of the Anet A6, providing a solid base for reliable operation.

This is a custom cover for the extruder fan. I swapped out the standard 40mm fan with a Noctua 40mm fan to significantly reduce noise levels. The Noctua fans feature a unique brown color that clashes with my OCD sensibilities, so I crafted this...

To mount the [8mm LJ18A3-8-Z/BX Autolevel Inductive Sensor For Anet A8 A2 A6 3D Printer](https://www.ebay.com.au/itm/8mm-LJ18A3-8-Z-BX-Autolevel-Inductive-Sensor-For-Anet-A8-A2-A6-3D-Printer-/283063661667?hash=item41e7e8b463).\r\n\r\nI couldn't find...

You'll need four hands to properly reattach the fan / heat sink / extruder stepper motor. I've tried it with just one screw removed, but it was essentially the same frustrating experience. I've since searched for alternative solutions from others...

UPDATE PLEASE USE FILES V5 Ive just updated these so they fit together better and nuts are easier to insert Hopefully this will be the last update Wanted a new extruder for my A8 Still learning how to use fusion 360 so thought a good place to start...

This modification enables the utilization of the CR10 or MicroSwiss full metal hotend on the Anet A8, AM8, or PK8. The auto-bed leveling sensor is an 18mm capacitive sensor. ...For the X belt, I employed this belt holder:...

I've successfully printed numerous projects, but each one has presented its own set of challenges, particularly when working with my Anet A8. ...This time around, I'm choosing to start over from the ground up and incorporating the best design elements...

I've upgraded the Super Simple ANET A6 E3D Carriage with a 12mm sensor. This addition allows for better precision and accuracy in the printing process. In addition to the new sensor, I've also increased the number of mounting holes for the x-end...

I've upgraded this LED mount to withstand the extreme temperatures generated by an E3D V6 hot end. The original design was prone to warping over time due to heat exposure. To address this issue, I increased the thickness of the LED bar, which makes...

This design serves as a mounting bracket for a 3D-Touch or BL-Touch sensor on an Anet A6 3D printer, enabling auto bed leveling functionality. The bracket allows for the sensor to be mounted directly beside the extruder nozzle at its right side,...