anet a6 upgrade extruder 3d models

Finalizer for the Z-axis. Requirements: - 1 M4x25 Screw - 1 M3x15 Screw - 1 M4 Nut - 2 M3 Nuts - 1 Pencil Spring. ...Support without clip included if you have the motor.

Vibration suppressors are employed to mitigate the adverse effects of resonant frequencies on equipment and structures. ...These devices function by absorbing or redirecting vibrational energy, thereby reducing the amplitude of oscillations and...

This is my very first 3D object, so be gentle with me. I made some tweaks to the original component for the 18mm proximity sensor: moved the ring a bit lower since otherwise you can't grip it firmly with the bolt; added a T-bar on the top fan ring to...

I'm a YouTube video: https://www.youtube.com/watch?v=sx0xTL40XhU This 3D print features 20% infill and three-layer walls with supports. To prepare cuts and generate G-code, I rely on Inkscape along with the gcodeplot plugin from GitHub:...

This fix enhances the original design found at Thingiverse, specifically thing 2776244. The inspiration comes from things 2609797 and 2387420. ...A major issue with the standard model is that its components often failed to assemble properly or exhibited...

<p>This is a quick re-mix of <a href="https://www.thingiverse.com/thing:1764285">a nice filament guide</a> by <a href="/papinist">papinist</a>.</p> <p>I remade it in FreeCAD to clean up the lines and to correctly align the ring to the holder. I also...

I finally gave up fighting a stubborn screwdriver and a recalcitrant wingnut on a bed frame with stripped-out holes. ...Instead, I opted for a 3M Locknut that does the trick.

To set the zero point, adjust the arm to level and secure the glass plate or replace the spring.

I've fine-tuned the lubrication pathways for: https://www.amazon.com/Igus-Slider-Bearing-8mm-Drylin%C2%AE-RJ4JP/dp/B01M4JZ81S

<p>Simple and curvy (aerodynamically friendly) Is simple and it works way better than the original. ...The best result is achieved printing it with two perimeters and support (with the base rotated at 30º) 0.2 mm layer height.</p> Category: 3D Printer...

This remix is based on qrisonline's original design found at thingiverse.com. I've made significant changes to improve its overall structure, making it stronger and more durable. The front hole has been enlarged to accommodate a 5MM bolt, while also...

Support to fix the motherboard and 2 mosfet

Here's a redesign that widens the part to securely capture the nut and position the fastener head more deeply within it. The overall strength of the part has been increased. A thread locking nut can be used if desired. ... This redesigned component is...

Allows the belt to be fixed under the tray easily and without deforming it.

Allows for easy belt maintenance

This is my version of the FanDuct, direct two-stranded cooling of pressure and not the nozzle. So there's still enough space available so that the exhaust air can also go away and no air cushion like on most ring fans forms, which prevents the cool...

I wanted to achieve perfect alignment of the Y belt, so I created a custom holder that would accommodate both thick and thin belts equally well. Designed with precision, it includes spacers to keep low bolts from pushing the bed upwards. ...A crucial...

Modification of the original piece adding a final cap on the left side for the car's end stop.

Support for SD Card Holder Implemented. Designed with a two-piece structure, eliminating the need for additional supports. Alternative mounting options include the 3mm diameter screw holes, bypassing the flange requirement. The tab is angled at 99...

This is a 12V 24 SMD LED Panel Mount. You can find it at http://s.aliexpress.com/R36VNN7R. To install it, use two M3 screws and nuts. The panel's beam has a hole that allows you to run the LED wiring through it. ...I only used a support for the cover,...

I built this to calm down the mother base with a brushless fan that spins at 12V from the power supply, measuring 5x5 cm in size. To secure the fan, I applied glue. ... To connect the set to the structure, you can use a small screw, but I suggest using...

Be extremely cautious - this device can shatter your front and rear plates at any moment. The front clamp is compatible with the following model: https://www.thingiverse.com/thing:1896013. The rear clamp, on the other hand, requires the specific...

Because the exit opening on the original air nozzle was too small for me, I drew a new air nozzle. The old nozzle had an outlet of 1mm x 14mm. The new one has an outlet of 4mm x 25mm. ...Therefore, the cross-sectional area increased sevenfold.

A compact LED bar is positioned discreetly behind the main display unit.

The laser-cut holes in the acrylic plates are slightly oversized for the linear rods, causing them to rattle when printing. Engineered to attach on the opposite side of the rod retainers or directly above the Z motor mounts, these inserts help...

Power meter enclosure designed to attach atop LCD housing found in another project: https://www.thingiverse.com/thing:2560566 This housing provides ample space to mount a 12V - 5V, 3A USB power supply unit for the Raspberry Pi Zero W installed...

The manufacturer fine-tuned the product by adjusting the top holes from 7.98mm to 8mm, eliminating the need for any additional drilling if it becomes overly snug. ...I'm impressed with the streamlined design, which also minimizes plastic waste.

i got tired of battling a screw driver and a wingnut on stripped out bed frame holes. ...uses a 3m locknut.

I released an updated version V2 of this project! You can find it here https://www.thingiverse.com/thing:2614129. This is a custom holder designed specifically for small LED panels that I discovered at a dollar store. You can also find similar ones...